Test & Measurement

Elspec G4500 Portable PQA with GPS receiver

Portable PQA with GPS receiver to to measure, store & analyze (continuously) waveform signals. Includes G4500 with 4x 3000A Flexible Current Clamps and GPS Receivers, Suitable for Applications like Utilities (Transmission, distribution, generation) and Energy Consumer (Critical power, industrial, commercial, etc.)

C.Scope DXL4 and SGV4 Cable and Pipe Locator

Cable and pipe avoidance and location tool with depth measurement. Simultaneous dual 33+131 kHz frequency will assist in the detection of smaller buried pipes and cables such as telecoms, cast iron and street lighting spurs. 4 available power levels up to 1 watt and depth detection approximately 3 meters (depending on soil type and operating mode). Four detection modes; Power, Radio, Generator and Allscan. Features a Dynamic Swing Sensor to aid in cable and pipe location.

PosiTector 200 B & C Ultrasonic Coating Thickness Gauge

Defelsko PosiTector 200 Advanced ultrasonic coating thickness gauge with type B & C Probes. Measures coating thicknes over wood, concrete, plastics, composites etc. Will measure up to 3 individual layer thickness in a multi-layer system and features a graphic readout. Supplied with both B, 13~1000um for wood, plastic and composites and C probes 50~3800um for coatings on concrete, fibreglass etc. Accuracy is +/- 2um +3% of reading.

Defelsko 6000 Ferrous & Non Ferrous Coating Thickness Tester

Ferrous/Non Ferrous metal coating thickness tester with storage of up to 100,000 readings. Supplied with external probe, calibration standards and carry pouch. Measurement range 0 to 1500um or 0 to 60 mils (selectable). Tolerance +/- 1um +1% of reading 0-50um, +/-2um +1% greater than 50um. Resolution 0.1um. Backglow display, HiLo limits audible & visible alerts when measurements exceed specified limits. Continually displays updates average, standard deviation, min/max thickness and number of readings while measuring. Built in USB, Bluetooth and Wifi for downloading readings.

Defelsko Positest Pull Off Adhesion Tester for Con & Metal

Measures the force required to pull a specified test diameter of coating away from its substrate using hydraulic pressure. Pressure is displayed in both MPa and PSI on a precision dial indicator and can be related to the strength of adhesion to the substrate. Suitable for coatings on both metal and concrete surfaces. Conforms with standards ASTM D4541 and ISO 4624.

Fischer FMP30 Feritscope

Fischer Feritescope FMP30 suitable to measure ferrite content in austenitic steel and duplex steel. Supplied with Probe FGAB1.3-Fe and calibration standard set..Non-destructive measurement of the ferrite content in a range from 0.1 to 80 % Fe or 0.1 to 110 FN. Data memory up to 20,000 readings and 100 applications for measurement data and application-specific calibrations.

Fluke 1738 Power & Energy Logger

Fluke 3 phase power logger with fluke connect mobile app. Includes 4x1500amp flex probes (1A~150A 100mA resolution 30mA accuracy) and 4x6000amp 1m flex probes. Copy logged files to USB memory stick. Measures to 50th harmonic. Can be powered off phase one if required. 4hr backup battery operation. 1000V CAT III / 600V CAT IV . Colour Touch Screen. Displays real time waveforms and FFT.

Fluke 1777 Power Quality Analyzer

The Fluke 1777 automatically measures power and power quality parameters. At a glance power quality and power health parameters. Capture high-speed transients at up to 8kV. Powers directly from the measurement circuit without a line chord. Many communications options. USB, WiFi ,Ethernet 7 cellular interface options. Includes internal GPS module for timing.

Fluke 345 Power Quality Clamp Meter

Ideal for measurements on switching loads such as variable frequency drives, electronic lighting and UPS systems. Low-pass filter and high EMC immunity design make unit ideal for noisy environments. 600V CAT IV rated, 1400A AC, 2000A DC. Measure and log harmonics, inrush current, ripple current on battery systems. Analyse data and generate reports with included Power Log software.

Fluke i40S-EL 3x40A CTs for secondary msmt 1777 or 1738

The Fluke i40s-EL Current Clamp-on Transformer is used for low current measurement as an accessory to the Fluke 1738 or 1777; suitable for making measurements up to 40A, and also measures accurately on 1A and 5A secondary current transformers. The i40s-EL jaw is capable of being clamped on current conductors up to 15mm in diameter.

Fluke MDA-550 Motor drive analyzer 4 channel

Fluke MDA-550 is a Motor drive analyzer designed to monitor and troubleshoot VFD (or VSD) motor systems. Features 4 channels, measurement to the 51st harmonic, 3x voltage probes with 1000V input range, 3xcurrent clamps 40~400A switchable, SVS-500 shaft voltage set with brushes, extension rod and magnetic base including high frequency probe. All CAT IV 600 V / CAT III 1000 V safety rated.

Fluke VR1710 Single-Phase Voltage Quality Recorder

Single phase voltage quality analyser. Records RMS, transients, flicker & harmonics up to the 32nd. Selectable logging periods from 1 sec to 20 minutes. Provides continuous recording with no gaps. Includes software for download, analysis and automatic reporting.

GE DynaMic rebound hardness tester

The GE DynaMic makes hardness testing quick and easy. The simple operation of this unit allows the user to position the impact devices and read the hardness value, all in a matter of seconds. The DynaMic provides readings in HV, HB, HRC, HRB, HS, HL, and M/mm2. This advanced unit will compensate for changes in testing direction. The Data Logger model can internally store hardness values along with statistical information. Features: • Measurements can be conducted in any direction without the need for calibration • Rebound hardness testing standardised according to ASTM A956 and DIN 50156 • Ergonomic, lightweight design (0.3 kg) • Test attachments for curved surfaces Applications: • Solid, coarse-grained components • Machine parts made of steel and cast aluminium alloys • Large series parts during production • Heavy forgings

GE Everest Ca-Zoom

GE Everest Ca-Zoom and hand-held controller is a portable, case-mounted, camera controller with real-time, multitasking software operating system which supports file storage on 64 MB of internal flash memory and CompactFlash removable storage media. Provides for integrated image capture and full motion video recording capabilities. Includes connectors for camera, handheld controller, video input/output, USB streaming, and keyboard for text generation. Supplied with 30 meter camera head cable and Extension Pole 1.8 to 3.6m. Camera heads must be chosen separately, see model GE,EVEREST PT-70 and GE,EVEREST PTZ-140.

GE Everest PTZ-140 Camera Head

The PTZ-140 is 140mm diameter colour camera module (fits through a 140mm opening) and features a 360deg pan, 234deg tilt, 36x optical and 12x digital zoom, high-intensity lighting and waterproof packaging to 45 m or 4.5 bar (when pressurised). Requires the GE,EVEREST CA-ZOOM to operate.

GE Everest PTZ-70 Camera Head

The PTZ-70 camera is 70 mm in diameter (fits through a 76mm opening) and features 10x optical zoom and 4x digital zoom for a total of 40x zoom. Eight 5-watt LED lights with variable intensity control, 360 degree continuous pan direction and 270 degree tilt capability. Waterproof to 45m or 4.5 bar (when pressurised). Requires the GE,EVEREST CA-ZOOM to operate.

Hach AS950 Water Sampler

Advanced water sampler for fully programmed collection. Samples are collected in up to 24, 1 Litre disposable plastic containers based on a set time period. Fitted with NEMA 4X,6 (IP67) sealed controller featuring a built-in pump.

Hioki PQ3198-94 Power Quality Analyzer

Premium Power Quality Analyzer in accordance with the IEC61000-4-30 Class A standard for demanding applications. Includes 4 x CT7045 6000A AC flexible CTs and 4 x CT7742 2000A AC/DC CTs. Ideal for AC mains studies as well as solar inverter evaluations. Supplied with PQ ONE power quality analysis software for detailed data analysis and report generation.

Hioki PW3365-20 Power logger

PW3365 Clamp on Power logger comes with Hioki's newly developed no-metal-contact voltage sensor. it measures voltage simply by clamping the sensor around an insulated wire. Measures single phase 2 wires, Single phase 3 wires, Three phases 3 wires, Three phases 4 wires - Current 3 channel only. Supplied with 3 x 1000A AC 9669 CTs and Power Logger Viewer software.

Mitutoyo SJ-210-NATA Surface Roughness Tester

Comprises LCD display and a detachable detector/drive unit. Parameters measured in Ra, Rq, Ry, Rz, Rt, Rp, R3z, Rk, Rpk, Rvk, S, Sm, Pc, mr, Mr1, Mr2, A1, A2, Vo units. Ranges: 350, 100, 50um & 10um, resolution from 0.01~0.4um. Tip radius 5mm. Data output. NiCd batteries.

Olympus 27mg Pocket Thickness Gauge

Range 1~500mm, fast min mode. Resolution 0.01mm. Probe operates -20~150 DegC.

Olympus 38DL Ultrasonic Thickness Gauge

The Olympus 38DL Plus Ultrasonic Thickness Gauge performs non-destructive measurements. This unit is supplied with D790-SM and D7906-SM transducers suitable for steel. Capable of THRU-COAT and Echo-to-Echo measurements on painted and coated surfaces. This handheld device is commonly used to measure the remaining thickness of pipes, tubes, tanks, pressure vessels, hulls, and other structures affected by corrosion or erosion. Colour transflective VGA screen, Rugged design for IP67. Data logging capability

Olympus 38DL thickness gauge probe

Probes suitable for Olympus 38DL thickness gauge 1 x M2008 Probe 1 x M202-RM Robe 1 x M1036 Probe 1 x M109-RM Probe

Olympus IPLEX GL 2m x 4mm Handheld Videoscope

Olympus IPLEX G Lite 2 meter, 4mm diameter handheld videoscope has the following features; • Daylight viewing monitor • 60fps for smooth video and still imagers • Dynamic image optimisation, reduces halation, balances exposure and optimises gain quality • Noise reduction, minimises noise and ensures accurate colour reproduction • Constant video recording and video bookmarking • Wireless image sharing (with iOS app "IPLEX IShare" only)

Olympus IPLEX GL 3.5m x 6mm Handheld Videoscope

Olympus IPLEX G Lite 3.5 meter, 6mm diameter handheld videoscope has the following features; • Daylight viewing monitor • 60fps for smooth video and still imagers • Dynamic image optimisation, reduces halation, balances exposure and optimises gain quality • Noise reduction, minimises noise and ensures accurate colour reproduction • Constant video recording and video bookmarking • Wireless image sharing (with iOS app "IPLEX IShare" only) • Optional UV and IR light sources

Olympus IPLEX GT 7.5m x 6mm Portable Industrial Videoscope

The Olympus IPLEX GT is designed for the visual inspection of heat exchangers, turbines, gearboxes, automotive parts, aircraft, and other industrial machinery. This lightweight videoscope comes with a 7.5m long, 6mm diameter tungsten braided insertion tube. Record still images and video simultaneously with Smart Video. Features: • 8" LCD monitor • Easy-to-use touch screen and hot key controls • Smart Video • TrueFeel articulation • Compliant to MIL-STD-810G

Olympus IPLEX RX 3.5m x 4mm Videoscope with Measurement

Olympus IPLEX RX, battery powered videoscope. 3.5 meter x 4 mm insertion tube, 4 way, 130 deg articulation and 120 deg FOV. Stereo Measurement functions, Distance, Point-to-line, Depth and Area. Applications include inspection of heat exchangers, turbines, gearboxes, automotive parts and aircraft. Still and video recording to USB flash, approx 3,400 images and 30 mins per 1 GB.

Olympus OmniScan MX2 Phased Array Flaw Detector

Second generation OmniScan MX2 with 32:128PR phased array acquisition unit, including a UT conventional channel. Included weld software option, ToFD software option and Multigroup software option. Suitable for weld inspection, composite inspection, corrosion inspection etc…

PCWI 30kV DC Porosity, Holiday Detector

DC Porosity (Holiday) detector. Detects pinholes in coatings above 150um on metal substrates such as pipes and tanks. 0-30kV, 3.5 digit LCD display with battery indicator, display of voltage level. Alarm indicated on front panel, supplied with rechargeable battery, 10h charger, probe handle with neon and 2m length cable, 60mm connector for flat brushes, 7m earth cable with clamp, fan brush, 250mm flat brass wire brush, 450mm probe extension. Dry conditions.

PCWI 40kV Pulse Porosity (Holiday) Detector

Pulse porosity (Holiday) detector. Detects pinholes in coatings and wrapping above 150um on metal substrates such as pipes and tanks. Can be used on dry or wet surfaces. 0~40kV output, 4 digit LED display of voltage, alarm sensitivity setting between dry and wet. Supplied with rechargeable battery, 10h charger, red probe handle and 2m length of rubber coated cable, 60mm connector for flat brushes, 7m earth cable with clamp, fan brush, 250mm flat brass wire brush, 450mm probe extension and 80mm probe extension.

Rae Systems Minirae 3000 VOC Gas Monitor

A reliable PID for VOC measurement. This industry standard 10.6eV photo ionisation detector measures from 0 to 15,000ppm of volatile organic compounds, referenced to isobutylene. Used by environmental scientists for detailed site investigations of soils and measuring the headspace in wells. It is also used for confined space monitoring, with low, high, STEL and TWA Alarms triggering 95dB buzzer and RED LEDs The instrument is supplied with " A calibration certificate for your records " A rechargeable battery pack rated for 16h operation " An alkaline battery adaptor, to extend your time in the field " A Flexi probe and 2 water trap filters

Remote Area Power Supply 150Ahr

Remote Area Power Supply 150AHr Lithium Battery with 12V output. To be used with TR,SOLAR. 2 Solar panels can be connected if necessary.

Additel 681AEx Digital Logging Pressure Gauge 7 bar

Additel 681AEx digital pressure gauge. Range: -1 to 7 bar, (-100 to 700 kPa), (-15 to 100 psi). Gauge or Absolute pressure Data logging (up to 10,000,000 records) Intrinsically safe Bluetooth communication Accredited to ISO/IEC 17025 NATA certified

Additel 681AEx Digital Logging Pressure Gauge 1 bar

The Additel 681AEx Digital Logging Pressure Gauge 1 bar is a high-precision, intrinsically safe pressure measurement instrument designed for demanding industrial environments. Ideal for professionals in process industries, calibration labs, and hazardous locations, this advanced gauge enables accurate pressure monitoring, logging, and troubleshooting where safety and reliability are paramount. Manufactured by Additel, the Additel 681AEx Digital Logging Pressure Gauge 1 bar is engineered for both performance and safety. With a 1 bar pressure range, this device is perfect for low-pressure applications requiring precise data logging and real-time monitoring. The gauge features a robust, intrinsically safe design (ATEX/IECEx certified), making it suitable for use in hazardous areas. Its high-accuracy sensor, large backlit display, and extensive data logging capabilities ensure reliable results for pressure calibration, leak testing, and process monitoring. Rent or hire the Additel 681AEx to streamline your pressure measurement tasks with confidence and efficiency. Key Features: Intrinsically Safe Design: Certified for use in hazardous environments, ensuring operator safety and compliance. High Accuracy: Delivers precise pressure measurements with an accuracy up to ±0.02%FS, ideal for critical applications. Comprehensive Data Logging: Built-in memory for extensive pressure data recording, supporting detailed analysis and traceability. Large Backlit Display: Easy-to-read digital interface for clear visibility in all lighting conditions. Versatile Pressure Units: Supports multiple engineering units for flexible operation across various industries. Rugged Construction: Durable housing designed to withstand harsh industrial environments and frequent field use. Why Choose the Additel 681AEx Digital Logging Pressure Gauge 1 bar? Exceptional measurement accuracy for reliable pressure monitoring and calibration. Certified safety for use in hazardous and explosive atmospheres. Advanced data logging and user-friendly interface for efficient workflow. TechRentals provides the Additel 681AEx Digital Logging Pressure Gauge 1 bar on flexible rental terms, giving you access to premium equipment without the upfront cost of ownership. Backed by over 50 years of industry expertise, we help ensure accurate and efficient pressure measurement and logging. Enquire today to rent the Additel 681AEx Digital Logging Pressure Gauge 1 bar and streamline your pressure monitoring and calibration tasks. Not sure which equipment to hire? Call our friendly experts today and get the right solution for your project.

TESTPRO CV100-K50 Copper Cable Certifier

TestPro CV100-K50 supports testing and certification for network deployments up to 40 Gigabit Ethernet for Cat 5e, 6, 6A, 7, 8 or Class I/II cabling system. The electrically centered test plug offers a frequency range of 3000 MHz which exceeds the Cat 8, Class I/II 2000 MHz requirement.

Aeroqual Logging Ozone Monitor - indoor air quality use

Portable ozone monitor fitted with low concentration-range detection head. Operating range 0~0.5ppm ozone with display in ppm or mg/m3. Gas sensitive semiconductor [GSS] sensor for accurate low-level measurements, T90 response approximately 100s. Operation from mains power supply or battery pack (4h operation). Internal data logging for 8000 points with software and cable for download to PC, or data logging direct to PC. Application for indoor air quality measurements.

Aeroqual Dust Sentry Profiler Outdoor Dust Monitor

Aeroqual Dust Sentry Profiler Outdoor dust monitor. This will monitor data and store the information in the cloud. This instrument will log PM1 200ug/m3 range, PM2.5 2000up/m3 range, PM10 5000up/m3 range 5000ug/m3 & TSP range 5000ug/m3. Accuracy +/-5ug/m3 + 15% of reading. Lowest detection limit <1ug/m3.

Ametek DFS3-200 Force Gauge

Range - 0 to 1000N / 0 to 100 Kgf. Accuracy 0.1% and resolution 0.01 in N and 0.001 in Kgf. Suitable for variety of application and measurements - Peak Tension and Compression, Break Tension and Compression, Load Average/Time. Comes as standard with a USB-C connection used for communication and charging with supplied cable and connection to PC with ForceTest software.

Ametek DVPlus RV Viscometer

Ametek DV Plus RV Viscometer. Range 100 to 40 million Centipoise(cP). Supplied with temperature probe and DVPlus connect app.

Anritsu MS2712E 4GHz Spectrum Analyser w Tracking Gen & GPS

The handheld Anritsu MS2712E 4 GHz Spectrum Analyser with Tracking Generator and GPS is ideal for field testing of spectrum monitoring, broadcast proofing, RF & microwave measurements, and Wi-Fi & wireless network measurements. You can store up to 2,000 traces and setups on-board or on a USB flash drive. Set-up time is minimised and information is effectively organised with the Trace Save-on-Event and one-button envelope creation features. Features: • Tracking generator -50 dBm to 0 dBm in 0.1 dB steps • Dynamic range 102 dB • DANL -162 dBm • GPS tagging of saved traces

Anritsu MW82119B, 2100 MHz PIM Master with Site Master opt

Anritsu MW82119B Passive Intermodulation (PIM) analyser with measurement frequency 2100 MHz and Site Master (cable and antenna analysis) options. Portable battery-operated, high power for the major wireless standards. Verify PIM performance at difficult to access sites such as Remote Radio Head (RRH) installations or indoor Distributed Antenna Systems (DAS). PIM measurements include PIM vs time, sweep PIM, distance to PIM (DTF), 1-port phase and smith chart.

Anritsu MW82119B, 850 MHz PIM Master with Site Master opt

Anritsu MW82119B Passive Intermodulation (PIM) analyser with frequency, Cellular 850 MHz band and Site Master (cable and antenna analysis) options. Portable battery-operated, high power for the major wireless standards. Verify PIM performance at difficult to access sites such as Remote Radio Head (RRH) installations or indoor Distributed Antenna Systems (DAS). PIM measurements include PIM vs time, sweep PIM, distance to PIM (DTF), 1-port phase and smith chart.

Anritsu S331E 4GHz Site Master Cable & Antenna Analyser

Cable and antenna analyser, frequency range 2Mhz to 4GHz. Measures return loss, VSWR, cable loss, and Distance To Fault. Suitable for legacy networks in addition to the new 3G and 4G networks being installed. Applications include cable & antenna installation and maintenance for wireless service providers

Anritsu S332E Site Master incl Spectrum Analyser

Anritsu antenna and cable analyser 2MHz to 4GHz and spectrum analyser 100KHz to 4 GHz. DANL -152dBm. Measures return loss, VSWR, cable loss, and Distance To Fault. N(f) Type port. Analysis software containing DTF and Smith chart tools included. Complete with calibration standard, AC/DC adaptor, and 12VDC car adaptor. Cable & antenna installation and maintenance for wireless service providers, contractors, military, aerospace and defence, and public safety applications.

Anritsu S412E LMR Master

The Land Mobile Radio (LMR) Master S412E is a compact handheld multi-function mobile radio analyser that has been specifically developed for technicians and engineers who install and maintain public safety, utility and private mobile communications systems.

Anritsu S820E Microwave Site Master 1 MHz to 20 GHz

Microwave antenna and cable analyser, frequency range 1 MHz to 20 Ghz with 110 dB dynamic range. Coaxial and waveguide system measurements include 1-port Return Loss, VSWR, Cable Loss, Distance-To-Fault and VSWR, Smith Chart, transmission and phase measurements. Unit comes standard with USB interface, smith chart and software management tools. Supplied with K(m) type port (compatible with 3.5mm and SMA), the S820E Sitemaster also includes "Classic Mode" which allows former users of the S8X0D series to become immediately productive with a minimal additional effort. A range of waveguide calibration components are separately available to rent.

Anritsu Site Master Waveguide Components

Calibration components and wave guide to co-ax adapters for Anritsu S820x Sitemater. Set includes 1/8 and 3/8 shorts, termination, and waveguide to co-ax adapter.

ARL NGARA Environmental Noise Logger

The ARL NGARA is a Class 1 environmental noise logger designed for unattended monitoring that offers full measurement flexibility. It can be configured to record all sound continuously so noise data can be post-processed. The instrument is also capable of providing logged data, WAV data, and alarm/triggered details. The logger can be set to wake up automatically, and either begin a new logging session or power on its network interface. The on-board LCD and push-button interface makes for simple control and configuration of the logger. Features: • Class 1 Sound Level Meter • Includes Class 1 Acoustic Calibrator • 20 to 120 dB measurement range • A and C frequency response • Capable of storing raw audio data to USB storage

ARL NGARA Environmental Noise Logger with modem

The ARL NGARA is a Class 1 environmental noise logger designed for unattended monitoring. It offers full measurement flexibility. It can be configured to record all sound continuously so noise data can be post-processed. The instrument is also capable of providing logged data, WAV data, and alarm/triggered details. The ARL,NGARA-4G includes a 4G modem and provides email alarms for noise exceedance. Full data upload to the Noise Cloud is an option. Solar Panels for extended deployment are available. Features: • Class 1 Sound Level Meter • Includes Class 1 Acoustic Calibrator • 20 to 120 dB measurement range • 4G modem with email alarms included • Solar Panels for extended deployment available • Option for Noise Cloud

Solar Panel for ARL,NGARA-4G

Solar panel for extended operation of ARL,NGARA-4G

b2 electronics HVA45TD VLF and TD test set

VLF, DC, and TD test capabilities combined in one unit. Meets international test guides (e.g., IEEE 400.2-2013). VLF Sine wave - 0.01Hz to 0.1Hz frequency range, 45KV peak and 32.3KV RMS voltage range. DC - +/-45KV, VLF square wave - 0-45KV and Sheath test - 0-15KV. Manual and automatic test modes available. Supplied with b2 control center software for reporting. Built-in memory: up to 50 reports, 50 test sequences.

Beamex MC6 Multifunction Calibrator

NATA certified MC6 provides calibration capability for pressure, temperature, electrical and frequency signals with HART communication and Document Calibrator option included. Performs as a field-entry device (FED) allowing for the recording of non-calibration related maintenance results. Pressure modules included, -1 to 20 bar and 600 bar. DC voltage & current, frequency, and pulse measurement. RTD, thermocouple, and resistance simulation & measurement. Pressure accuracy EXT-600 bar 0.007% FS + 0.01% Rdg, INT-20 bar 0.005% FS + 0.01% Rdg, temperature coefficient ±0.001 % Rdg/degC outside 15 to 35 degC. Please enquire about our other MC6 configurations and pressure rangers.

Beamex MC6 Multifunction Calibrator PB

The Beamex MC6 Multifunction Calibrator PB is a versatile and high-precision calibrator designed for industrial applications. It is primarily used for calibrating and testing various process instruments, including pressure, temperature, and electrical signals. This advanced calibrator combines multiple functions into a single device, making it an essential tool for professionals in the field of instrumentation and calibration. The Beamex MC6 offers a user-friendly interface, robust construction, and high accuracy, ensuring reliable performance in demanding environments. It supports a wide range of calibration tasks, from simple measurements to complex calibration procedures, making it suitable for various industries, including oil and gas, power generation, and manufacturing. Key Features: Multifunction Capability: Combines pressure, temperature, and electrical signal calibration in one device. High Accuracy: Provides precise measurements with an accuracy of up to 0.005% of reading. Robust Design: Built to withstand harsh industrial environments with an IP65-rated enclosure. Intuitive Interface: Features a large, color touchscreen display for easy operation and navigation. Data Logging: Capable of storing calibration results and generating detailed reports. Versatile Connectivity: Supports various communication protocols, including HART, FOUNDATION Fieldbus, and Profibus PA. The Beamex MC6 Multifunction Calibrator PB is an indispensable tool for professionals seeking a reliable and efficient solution for their calibration needs. For more technical details, please refer to the manufacturer's website.

Beamex External Pressure Module

Beamex external pressure modules compatible with MC6, MC5, MC4, MC2 MC5-IS, MC2-IS and MC5P calibrators. Various rangers available, please inquire.

Bell 4190 MilliGauss Meter

Handheld digital ELF gauss meter. Maintains accuracy regardless of orientation. Applications include detecting magnetic field emissions from overhead AC power lines, video display terminals, office equipment and household appliances. Analogue o/p, data logging, auto range 0.1 to 1999 mG, minimum resolution 0.1 mG/.01 uT.

5180 FW Bell Gauss/Tesla Meter

Magnetic measuring equipment, portable gaussmeter. Built-in software eliminates the need for complex calibration procedures. Key features include Auto Zero, Min./Max./Peak Hold, Auto Range and Relative Mode. Allows the user to select Gauss, Tesla or Ampere/Meter readings. With Hall effect transverse probe STD18-0404. Frequency bandwidth DC - 20 kHz, range from 0 up to 30 kG with a basic accuracy of 1.1% (FS). Analogue output (+/-3V FS) and USB interface. Battery operated.

Bently Nevada TK3-2E Proximity Probe Test System

The TK-3 Proximity System Test simulates shaft vibration and position for calibrating proximity probes. The TK-3 uses a removable spindle micrometer assembly to check the transducer system and position monitor calibration. This assembly features a universal probe mount that will accommodate probe diameters from 5 mm to 19mm

BK MR 160V, 120A 3KW DC Power Supply

BK Precision MR3K160120, multi-ranging DC power supply allowing any combination of the rated 160 V and 120 A up to the maximum output power of 3000 W.

BK MR PVS 600V, 8.5A 3KW DC Power Supply

BK Precision PVS60085MR, multi-ranging DC power supply allowing any combination of the rated 600 V and 8.5 A up to the maximum output power of 3000 W.

BW Bump & logging download for BW,MICROCLIP

Automatic calibration testing and data management system for the BW microclip gas detection equipment. Carries out fully automatic "hands-free" calibration and functional bump test. It also enables data collected during operation of the BW microclip to be downloaded.

BW Microclip Charger cradle for 5 Microclips

Charging cradle for 5 BW Microclips

Honeywell BW Flex4 Muti-Gas Detector LEL, O2, H2S, CO

BW Flex4 Portable Multi-Gas Detector - Yellow/Black Large high-resolution display Simple one button operation H2S 0-200ppm, CO 0-2000pm, O2 0-30% vol, Catalytic LEL sensor 16hr battery life.

Honeywell BW Flex4 Muti-Gas Detector IR LEL, O2, H2S, CO

BW Flex4 Portable Multi-Gas Detector - Yellow/Black Large high-resolution display Simple one button operation H2S 0-200ppm, CO 0-2000pm, O2 0-30% vol, IR LEL 0-100% Two months of battery runtime on a 4.5hr charge with the low powered IR LEL sensor

IntelliDox Bump and Calibration Station for Flex4

Bump and Calibration station for BW,FLEX4 and BW,FLEX4-IR

BW Ultra 4 gas + CO2 pumped gas detector

The Honeywell BW Ultra is a pumped portable five-gas detector. The BW Ultra provides the functionality of a standard 4 gas detector (LEL, O2, CO, H2S). This configuration has a Carbon Dioxide (CO2) sensor installed in the 5th sensor position. If CO2 is a risk it must be monitored with a dedicated sensor. Sensors Flammables (catalytic LEL sensor): 0- 100% LEL, 1% LEL resolution Oxygen: 0.0% – 25.0% vol, 0.1% vol resolution Hydrogen Sulphide (H2S): 0.0ppm -100ppm, 0.1/1ppm resolution Carbon Monoxide (CO): 0 – 2000ppm, 1ppm resolution Carbon Dioxide (CO2): 0ppm – 50,000ppm, 100ppm resolution TechRentals supplies this gas detector in a Confined Space Gas Monitoring Kit. Sample probe and tubing for regular use also 3m sampling hose. IRDA Adapter and download. 14Hr battery life.

BW ULTRA 5- pumped gas detector - with Ammonia

The Honeywell BW Ultra is a pumped portable five-gas detector. The BW Ultra provides the functionality of a standard 4 gas detector (LEL, O2, CO, H2S). This configuration has an Ammonia (NH3) sensor installed in the 5th sensor position. Sensors Flammables (catalytic LEL sensor): 0- 100% LEL, 1% LEL resolution Oxygen: 0.0% – 25.0% vol, 0.1% vol resolution Hydrogen Sulphide (H2S): 0.0ppm -100ppm, 0.1/1ppm resolution Carbon Monoxide (CO): 0 – 2000ppm, 1ppm resolution Ammonia (NH3): 0 -100ppm, 1ppm resolution TechRentals supplies this gas detector in a Confined Space Gas Monitoring Kit. Sample probe and tubing for regular use also 3m sampling hose. IRDA Adapter and download. 14Hr battery life.

BW Ultra 4 gas + PID pumped gas detector

The Honeywell BW Ultra is a pumped portable five-gas detector. The BW Ultra provides the functionality of a standard 4 gas detector (LEL, O2, CO, H2S). With a PID installed in the 5th sensor spit you get the ability to detect toxic gases far below their explosive limit. Sensors Flammables (catalytic LEL sensor): 0- 100% LEL, 1% LEL resolution Oxygen: 0.0% – 25.0% vol, 0.1% vol resolution Hydrogen Sulphide (H2S): 0.0ppm -100ppm, 0.1/1ppm resolution Carbon Monoxide (CO): 0 – 2000ppm, 1ppm resolution VOCs: 0 – 1000ppm, 1ppm resolution TechRentals supplies this gas detector in a Confined Space Gas Monitoring Kit. Sample probe and tubing for regular use also 3m sampling hose. IRDA Adapter and download. 14Hr battery life.

Compu-Flow C6 Doppler and Ultrasonic Flowmeter

Compu-Flow Model C6 is an industrial-grade Doppler ultrasonic clamp-on flow meter designed for non-intrusive flow measurement. The unit uses proprietary microprocessing technology to provide Doppler-based flow readings. The Model C6 is suitable for a range of industrial flow measurement applications where clamp-on installation is preferred.

DataTaker DT80M 5 to 15 Ch Logger includes Built in Modem

Includes a built in GSM modem for internet access to the device supports 2G and 3G networks (GSM/GPRS/EDGE/WCDMA). Measures voltage, current, resistance and frequency. Up to 5 analogue (+/-30V) sensor inputs. Each channel is independent and supports: one isolated 3-wire or 4-wire input, or two isolated 2-wire inputs, or three common referenced 2-wire inputs. Store up to 10 million data points in user defined memory. Generally used at sample rates of 1Hz and slower.

DataTaker DT80 Expansion Module

Channel expansion module for DT80 data loggers. Adds 20 full datataker channels to the logger

Defelsko Positest Concrete Moisture Meter

Defelko Positest Concrete Moisture Meter. Concrete moisture meter using the electrical impendance to measure concrete moisture. Designed to do area scans the kit includes a telescopic extender. Measure 0~6% Moisture content of concrete, 0~4% Carbide Method equivalent or 0~100% RH. Accuracy +/-0.5% Moisture content of concrete. Tests in accordance to ASTM F2659

DILO SF6 gas MultiAnalyser

DILO SF6 gas MultiAnalyser (model part number - 3-038R-R302V2-B) measures the purity of SF6 gas and the level of humidity in gas insulated switchgear systems. Measures SF6 Volume, moisture and SO2 (0-100 ppm). Unit has Battery operation and/or external power supply and touchscreen display. USB flash drive with data file for evaluation and reading out of measuring results. Supplied multiple adaptors suitable for different switchgears. Refer accessory list for details.

Druck DPI611 2 Bar Pressure Calibrator

Fully self-contained pressure test and calibration system combines pressure generation, signal measurement and loop power. Generates from 95% vacuum to 2 bar/30 psi pneumatic pressure with 0.0185% FS accuracy. Calculates PASS/FAIL errors and documents results. User Guide stored in the memory of the instrument, 3-touch set-up for any application.

Druck DPI611 20 Bar Pressure Calibrator

Fully self-contained pressure test and calibration system combines pressure generation, signal measurement and loop power. Generates from 95% vacuum to 20 bar/300 psi pneumatic pressure with 0.0185% FS accuracy. Calculates PASS/FAIL errors and documents results. User Guide stored in the memory of the instrument, 3-touch set-up for any application.

Druck DPI 612 200 bar Pressure Calibrator

Fully self-contained pressure test and calibration system combines pressure generation, signal measurement and loop power. 0 to 200 bar, accuracy 0.005 %FS. Calculates Pass/Fail errors and documents results. User Guide stored in the memory of the instrument, 3-touch set-up for any application. Certified ISO/IEC 17025.

Druck PV411A Multifunction Hand Pump Kit

Provides up to 700 bar hydraulic, 40 bar pneumatic pressures and vacuum to -950m bar. Built-in stroke adjuster, lower pressure fine control and tamper proof overpressure protection.

EA Technology UltraTev Plus Partial Discharge Detector

Multi-function Partial Discharge (PD) Instrument. It measures accurate PD activity using the UltraTEV detector and an ultrasonic detector. It gives you an objective measure of the level of activity. Will display PD severity level. The kit includes the Ultradish for measurement of overhead assets.

Elspec Current Clamps (4 x 1-6A Mini Clamps)

Set of 4 x a-6A Mini Clamps suitable for Elspec G4500 unit

Emerson AMS Trex Device Communicator with HART & FFbus

The AMS Trex is an intrinsically safe HART and Foundation fieldbus device communicator. It allows technicians to configure, isolate, diagnose and repair problems while devices continue to run using the Loop power function and on board ammeter. Segment and loop diagnostic tools quickly validate loop and fieldbus segment characteristics for easy troubleshooting. This model has options L-"Device Communicator Plus Communication Module" and F-"HART + Foundation Fieldbus".

Emerson AMS Trex Device Communicator with HART

The AMS Trex is an intrinsically safe HART device communicator. It allows technicians to configure, isolate, diagnose and repair problems while devices continue to run using the Loop power function and on board ammeter. Segment and loop diagnostic tools quickly validate loop and segment characteristics for easy troubleshooting. This model has options L-"Device Communicator Plus Communication Module" and H-"HART".

Everest Ca-Zoom PTZ HD Camera System

The Everest Ca-Zoom PTZ HD Camera is a high-performance pan-tilt-zoom industrial inspection system designed for critical use in oil and gas, mining, pharmaceutical, and nuclear power industries. Built for harsh environments, it delivers exceptional Full HD clarity and long-duration video recording. Supplied with two interchangeable HD camera heads: PTZ HD30 – Full HD (1920x1080), 1/2.8" CMOS sensor with 2.38 MP and 4 high-intensity LEDs. PTZ HD10 – Full HD (1920x1080), 1/3" CMOS sensor with 5.14 MP and 10 LEDs for low-light visibility. Designed for versatility, it includes a 256 GB SSD (6+ hours recording), 30m cable, and 6ft deployment pole. The IP68-rated housing is waterproof to 50m when pressurised, ideal for submerged or hazardous inspections. Perfect for detailed remote visual inspections, the Everest Ca-Zoom PTZ HD Camera combines image quality, rugged build, and practical features for professionals needing reliability and precision.

Evident EPOCH 650 Ultrasonic Flaw Detector

EPOCH 650 Ultrasonic Flaw Detector is designed to meet the requirements of ISO 22232-1. Standard dynamic DAC/TCG and onboard DGS/AVG. Available test modes Pulse Echo, Dual, or Through Transmission.

Evident NORTEC 600D Eddy Current Flaw Detector

NORTEC 600D Eddy Current Flaw Detector is designed to meet the requirements of IP66 and EN-15548 compliant. N600D models supports Dual frequency and mixing, Conductivity and coating thickness measurement and Rotary scanner mode.

Evident OmniScan X4 PAUT Flaw Detector

OmniScan X4 64:128PR Phased Array instrument with 64 pulsers and 128 receivers, 2 UT P/R channels. TFM, FMC acquisition capability. Loaded with the latest revision of MXU 6.x software Detect and interpret challenging flaws and identify damage earlier with the powerful, yet portable OmniScan™ X4 multitechnology flaw detector. Exploit its versatile PA, faster TFM, innovative PCI, and efficient twin TFM/PCI to perform rapid and reliable inspections of welds and components.

Evident Splitter Connector for OmniScan unit

The Evident Splitter Connector for OmniScan unit is a specialised accessory designed to enhance the connectivity and versatility of your OmniScan flaw detector system. Ideal for professionals in non-destructive testing (NDT), this splitter connector enables seamless integration of multiple probes or accessories, streamlining complex inspection workflows and improving productivity on-site. Manufactured by Evident Scientific, the Evident Splitter Connector for OmniScan unit is engineered for reliability and precision. This essential component allows users to rent or hire a robust solution for advanced ultrasonic testing, phased array inspections, and other critical NDT applications. Its durable construction and precise signal management ensure optimal performance, making it a valuable addition to any professional’s toolkit for industrial inspections, asset integrity assessments, and quality control tasks. Key Features: Multi-Channel Connectivity: Supports simultaneous connection of multiple probes or accessories for efficient phased array and ultrasonic testing. Robust Signal Integrity: Maintains high-quality signal transmission, minimising interference and ensuring accurate data collection. Durable Construction: Built with industrial-grade materials to withstand demanding field environments and frequent use. Seamless Integration: Designed specifically for compatibility with OmniScan units, ensuring plug-and-play operation without additional configuration. Compact and Portable: Lightweight design makes it easy to transport and deploy in various inspection scenarios. Why Choose the Evident Splitter Connector for OmniScan unit? Delivers reliable and precise connectivity for advanced NDT inspections. Enhances workflow efficiency by supporting multiple probe configurations. Engineered for durability and consistent performance in challenging environments. TechRentals provides the Evident Splitter Connector for OmniScan unit on flexible rental terms, giving you access to premium equipment without the upfront cost of ownership. Backed by over 50 years of industry expertise, we help ensure accurate and efficient non-destructive testing operations. Enquire today to rent the Evident Splitter Connector for OmniScan unit and streamline your ultrasonic and phased array inspection tasks. Not sure which equipment to hire? Call our friendly experts today and get the right solution for your project.

Fitel S179 Core Alignment Fusion Splicer and Cleaver

Fitel S179 hand-held, core-alignment fusion splicer for single and multimode fiber, includes S326 cleaver. Typical 6 sec splice time, 9 sec heating time and losses of 0.02dB and 0.01dB on single and multimode fibre respectively. Features include 4.3-inch LCD touch screen, 3+1 LED lights illuminate entire splicing chamber for improved visibility in low-light and Intentional high attenuation splice function, splice loss of 0.1dB to 15dB(0.1dB step) can be made for an inline fixed attenuator.

FLIR E54 Infrared Thermal Imaging Camera

Temperature range -20 to 650 degC, IR resolution 320 x 240, 30Hz. Display 10cm 640 x 480 touchscreen, 1-4 continuous digital zoom, video recording, Wi-Fi, USB and Bluetooth enabled. IFOV 1.31 mrad. Image modes include infrared, visual, MSX and picture-in-picture. Features manual focus, moisture, insulation, above, below, interval measurement alarms and GPS image tagging. Applications include electrical distribution, mechanical (belts, rollers, couplings, gaskets/seals, compressors etc), product development, HVAC/R, automotive.

FLIR T640 Infrared Thermal Imaging Camera

FLIR high performance thermal imaging camera with on-board 5MP visual camera, 640 x 480 thermal resolution, IFOV 0.68, 8X continuous zoom, time lapse and GPS are just a few of its many features. The T640 has a temperature range -40 to 2,000 degC. Calibration certificate to 1,000 degC provided. If certification to 2,000 degC is required, please inquire.

Fluke 1524 Precision Handheld Thermometer

Precision portable, electronic thermometer with trending, memory for logging 15,000 data and time stamped measurements and 25 readings with statistics. Includes 5615 PRT probe, maximum immersion length 305mm, diameter 6.35mm. Temperature range -200 to 420 degC.

Fluke 1587 Insulation Multimeter

Fluke 1587FC Insulation Multimeter will test to 2GOhms. Includes Fluke Connect capability.50V, 100V, 250V, 500V & 1000V Insulation test capability. Using Fluke Connect can do PI/DAR, store, Temperature Compensation & VFD low-pass filter

FLUKE 1625 KIT GEO Earth Ground Tester

Measure total earthing resistance (RA) with 3 or 4-pole Fall of Potential method, selective earth resistance measurement and 4-pole soil resistivity testing (0.001 ohm to 19.99 k ohm). Stakeless ground loop measurements (0.001 ohm to 199.9 ohm). Includes automatic frequency control to minimise interference effects. Battery powered.

FLUKE 1630 Earth Ground Clamp

Earth ground loop testing and continuity testing without breaking the circuit. Ground loop resistance range 0.025ohm to 1.5KOhm. Ground leakage current measurement range 0.2mA to 1000mA. Current measurement range 0.2A to 30A. Logs and stores measurements for on screen recall. LCD display. Battery powered.

Fluke 1663 FVF Installation Tester

Fluke 1663 Installation Tester. Provides the following tests Continuity test under 200mA, Loop Impedance without triggering an RCD can be set for 10,30,100,300,500,650mA & 1A. Insulation resistance measurement under 1000V. Measure earth plug resistance by earth rods (Rods not in kit). Voltage measurements

Fluke 177 Multimeter

The Fluke 177 True-RMS Digital Multimeter is a high-accuracy, reliable tool designed for professional electricians and technicians. With True-RMS capabilities and a wide range of measurement functions, it's ideal for troubleshooting in both commercial and industrial environments. " True-RMS for accurate AC measurements, even with non-linear loads " Measures voltage, current, resistance, frequency, capacitance, and temperature " CAT III 1000 V / CAT IV 600 V safety rated for high-voltage environments

Fluke 2042 Cable Locator

Ideal for tracing cables in walls and underground, locating fuses/breakers on final circuits and locating interruptions and short-circuits in cables and electrical floor heating systems. Can be used for tracing metallic water and heating pipes. Supplied as a kit comprising a transmitter and receiver in a carry case. Voltage measurement range 12 to 400 volts. Frequency range 0 to 60Hz. Transmitter output signal 125kHz. Transmitter voltage 0 to 400V ac/dc. Depth location 0 to 2.5m. Receiver voltage detection range 0 to 0.4m. The receiver incorporates a torch for working in dimly lit locations.

Fluke 233 Digital Multimeter with Remote Display

Fluke 233 Remote Display Multimeter. The removable display has a range of 10 meters and allows the user flexibility when the meter and the display need to be in separate places. The Fluke 233 features temperature, True-RMS AC voltage and current for accurate measurements on non-linear signals, can measure up to 1000V AC and DC, up to 10A (20A for 30seconds), and features a capacitance range of 10,000µF.

Fluke 28II EX Intrinsically Safe True-RMS Multimeter

Fluke 28II Ex Intrinsically Safe Multimeter is a completely sealed IP67 rated case. For use inside and outside of hazardous zones. Measures up to 1000V, 10A AC and DC with true-RMS for accurate measurement on nonlinear signals. Frequency measurements to 200 kHz, resistance, conductance, diode test, capacitance, and temperature. Results are displayed on the bright, 4-1/2 digit LCD (20,000 counts).

Fluke 376 True-rms AC/DC Clamp Meter with iFlex

1000A ac and dc current measurement with fixed jaw. 2500A ac current measurement with the 45cm iFlex flexible current probe. 1000V ac and dc voltage measurement. Voltage and current measurements are true rms. Includes ability to measure frequency, resistance and capacitance. Rated CAT IV 600V and CAT III 1000V.

Fluke 381 Remote Display True RMS AC/DC Clamp meter w iFlex

The Fluke 381 Remote Display True RMS AC/DC Clamp Meter with iFlex is a versatile, high-performance clamp meter designed for professional electricians and technicians who require accurate, hands-free current measurements in demanding environments. Available exclusively for rent or hire, the Fluke 381 is ideal for industrial, commercial, and utility applications where safety, efficiency, and precision are paramount. Manufactured by Fluke, a global leader in electrical test equipment, the Fluke 381 combines advanced True RMS measurement technology with a unique detachable wireless display, allowing users to view readings remotely and operate the meter in hard-to-reach or hazardous areas. The included iFlex flexible current probe extends measurement capabilities up to 2500 A AC, making it perfect for large conductors and tight spaces. With features such as inrush current capture, min/max/avg recording, and CAT IV 600 V/CAT III 1000 V safety ratings, this clamp meter is engineered for reliable indoor and outdoor electrical diagnostics. Rent or hire the Fluke 381 to streamline your electrical testing, troubleshooting, and maintenance tasks with confidence. Key Features: Remote Detachable Display: Enables hands-free operation and safer measurements by allowing you to view readings up to 10 meters away from the measurement point. iFlex Flexible Current Probe: Expands measurement range to 2500 A AC and provides access to tight or awkward spaces for greater versatility. True RMS AC/DC Measurement: Delivers accurate readings on non-linear loads, ensuring precise diagnostics in complex electrical systems. Inrush Current Capture: Accurately records starting current for motors and other equipment, aiding in troubleshooting and preventive maintenance. CAT IV 600 V / CAT III 1000 V Safety Rating: Provides superior protection for users working in high-energy environments. Min/Max/Avg Recording: Tracks signal fluctuations over time for comprehensive system analysis. Why Choose the Fluke 381 Remote Display True RMS AC/DC Clamp Meter with iFlex? Unmatched measurement flexibility and safety with a wireless remote display and iFlex probe. Industry-leading accuracy and reliability for demanding electrical testing environments. Robust design and advanced features tailored for professional diagnostics and troubleshooting. TechRentals provides the Fluke 381 Remote Display True RMS AC/DC Clamp Meter with iFlex on flexible rental terms, giving you access to premium equipment without the upfront cost of ownership. Backed by over 50 years of industry expertise, we help ensure accurate and efficient electrical testing and diagnostics. Enquire today to rent the Fluke 381 Remote Display True RMS AC/DC Clamp Meter with iFlex and streamline your electrical measurement and troubleshooting tasks. Not sure which equipment to hire? Call our friendly experts today and get the right solution for your project.

Fluke 54-2B 2Ch Data Logging Temperature Meter w Flukeview

Fluke 54 series 2 dual input digital thermometer with data logging. Will take most TC inputs. Accuracy ±0.05% of reading +0.3 deg C. 500 point logging with date & time stamp. Also records min, max or avg. Logged data can be reviewed on meter or downloaded to PC using software included. Supplied with 2x 1m K type thermocouple leads -200 to 1,372 deg C. High temperature limit depends on thermocouple construction material. Custom TC provided have an approximate upper limit of 800 to 900 deg C.

Fluke 5500A Multi Product Calibrator

Calibrator sources direct voltage & current, alternating voltage and current, with multiple waveforms and harmonics, 2 simultaneous voltage outputs or voltage & current. Simulates power with phase control, resistance, capacitance, thermocouples and RTDs. Selectable ranges include the following outputs VDC from 0~1.02kV, VAC from 1mV~1.02kV with output from 10Hz~500kHz. AC current from 0.01µA~11A with output from 10Hz~10kHz. DC current from 0~11A. Resistance values from short circuit to 330Mohm. Capacitance values from 330pF~1,100µF. Temperature t/c B, C, E, J, K, L, N, R, S, T, U, RTD Pt385 100ohm, Pt3926 100ohm, Pt3916 100ohm, Pt385 200ohm, Pt385 500ohm, Pt385 1kohm, Ni120 120ohm & Cu427 10ohm.

Fluke 62 Max Plus

The Fluke 62 MAX+ Handheld Infrared Laser Thermometer delivers the accuracy you need. Just point, shoot, and read the temperature of many types of equipment. Get accurate readings form transformers, motors, pumps, panels, breakers, compressors, duct, steam lines, valves, and vents.

Fluke 725 Process Calibrator

Documenting process calibrator. DC voltage msmt. 0.025% 300 V max, source 0.02% 11 V max. DC current msmt. 0.025% 110 mA max, source 0.01% 22 mA max. Resistance msmt 0.05% 11 kohm max, source 0.01% 11 kohm max. Frequency msmt 5 counts 1 Hz - 50 kHz, source 1 count 20 Hz - 5 kHz. ‘K’ thermocouple msmt 0.3 deg C, source 0.3 deg C. Pt 100 RTD msmt 0.5 deg C, source 0.2 deg C. Will measure and simulate 4-20 mA,TC E N J K T B R S and C, 2, 3 and 4 wire RTDs and frequency. The unit operates from drycell batteries.

Fluke 754 Documenting Process Calibrator with HART

The Fluke 754 is a handheld, multi-function documenting process calibrator with HART communication. It is designed for the calibration, maintenance, and troubleshooting of test sensors, transmitters, and other instruments. The 754 allows for the testing of all common process parameters including volts, mA, Resistance Temperature Detectors (RTD's), thermocouples, frequency, and ohms. Compatible with all Fluke 700Pxx pressure modules, this device also allows for custom units, user-entered values during test, one and two-point switch testing, square root DP flow testing, and programmable measurement delays. Features: • Simultaneous source and measure capabilities • Create and run automated as found/as-left procedures • AutoStep - set an automated sequence of steps (with a delayed start if required) • Records and documents results

Fluke 773 Milliamp Process Clamp Meter

Measure 4-20 mA control lines, PLC loops, transmitters or any 4-20 mA line without breaking the loop. Capable of 0-20.99 mA and 24-100 mA with clamp. Source and simulate mA and voltage signals in circuit. 4-20mA scaled o/p

Fluke 789 Process Meter

The Fluke 789 ProcessMeter is a compact digital multimeter and mA loop calibrator solution. Features include standard multimeter functions with 2 to 20mA sink and source capability, with a 24V supply, HART 250 resistor and 20mA drive into 1200 ohms. Simultaneous mA and % of scale readout on mA output. 25% manual step plus auto step and auto ramp on mA output. Min/max/average/hold/relative modes. Double size dual display. Accuracy, VDC 0.1% +1, VAC 0.7% +2, mA DC 0.05% +2, frequency 0.005% +1. Certified ISO/IEC 17025.

Fluke 9062 Phase Rotation Indicator

Fluke 9062 provides rotary field and motor rotation indication with the benefits of contact-less detection.indication of 3 phase rotation using test leads supplied or can be used to determine motor rotation on synchronous and asynchronous 3 phase motors.

Fluke 9170 Dry Block Temperature Calibrator -45 to 140°C

Fluke 9170 dry well calibrator temperature range -45 to 140°C in normal room conditions. This product has a large LCD display, numeric keypad, and an on-screen menu. The display shows the block temperature, cut-out temperature, stability criteria, and ramp rate. Certified ISO/IEC 17025.

Fluke DSX-5000 Cable Analyser 1GHz Class FA

Fluke DSX-5000 1GHz cable analyser copper test solution enables testing and certification of twisted pair cabling for up to 10 GigE deployments and will certify shielded and unshielded structured cabling systems from Cat 3, to 7A and Class C, to FA at Level V accuracy. 9 second Cat 6 autotest. Built in Alien Crosstalk testing capability. PLA004 (Cat 6A / Class EA), CHA004 (Cat 6A / Class EA) adapters and LinkWare PC reporting software included.

Fluke DSX-8000 Cable Analyser 2GHz Class FA

Fluke DSX-8000 2GHZ cable analyser copper test solution enables testing and certification of twisted pair cabling for up to 40 GigE deployments and will certify shielded and unshielded structured cabling systems for Cat 5E,6,6A, 7A, 8 and Class C I/II, to FA at Level V accuracy. 8 second Cat 6 autotest. Built in Alien Crosstalk testing capability. PLA004 (Cat 6A / Class EA), CHA004 (Cat 6A / Class EA) adapters and LinkWare PC reporting software included.

Fluke CertiFiber Pro MM-SM Optical Loss Test Set

Fluke multi and singlemode (CFP-Q-ADD) optical loss test set modules for the Versiv DSX-5000. Provides Tier 1 certification at 850, 1300, 1310 and 1550 nm in 3 seconds (for 2 wavelengths). A set reference wizard ensures correct reference setting. Encircled Flux compliant as required by ANSI/TIA and ISO/IEC. Measures fibre optic attenuation, length, and propagation delay. Includes built in VFL and Linkware software.

Fluke FTK1000 Multimode Fibre Optic Light Source and Meter

Fluke SimpliFiber FTK1000 fibre test kit. Light source is multimode 850nm and 1300nm. Power meter has 850/1300nm multimode and 1310/1550nm single mode. Manage results and print reports via Power meter memory, PC and supplied software.

Fluke 80i-110s AC/DC Current Probe

Current clamp for oscilloscopes which uses a Hall effect cell for the measurement of DC or AC current. Measures currents from 0.05 to 100A peak. A thumbwheel can be used to reset zero for adaption to the measurement environment. The clamp can be used with any measurement instrument which has a BNC input and an impedance of 1MOhm, <100pF. Maximum conductor diameter, 11.8mm

Fluke i5sPQ3 AC Current Clamps, 5A (3 x i5S per set)

A pack of 3 pieces of the i5s 5A AC current clamps, specially configured to provide low current accuracy while taking measurements on secondary current transformers. CAT III 600 V (For insulated conductors only). Suits the Fluke 435 and other instruments with BNC inputs.

Fluke ii900 Ultrasonic Industrial Imager

Fluke ii900 ultrasonic visual imager, Displays the location and magnitude of compressed air leaks. Operates from 2kHz~52kHz will detect leaks of .0025L/sec at 7bar from 10meters. Sunlight readable display. Frequency band selection. 6hrs of battery life. Recharge time 3hrs.

Fluke ii910 Precision Acoustic Imager

Fluke ii910 Precision Acoustic Imager. Suitable to locate partial discharge, corona discharge as well as gas and vacuum leaks. Frequency range 2KHz to 100KHz and detection range 0.5 to > 120 meters. Internal memory with the capacity for 999 picture files and 20 video files. 6hrs of battery life. Recharge time 3hrs. Updated with new MecQ™ mode

Fluke Optifiber Pro Quad OTDR

Fluke Optifiber Pro Quad multi and singlemode OTDR, wavelengths 850, 1300, 1310 and 1550nm, dynamic range 28, 30, 32 and 30 dB respectively. Designed for testing, troubleshooting and certifying multi and singlemode fibre optic networks. Smartphone user interface, shortest event and attenuation deadzones, LinkWare download and reporting software included.

Fluke 200 MHz 4 CH ScopeMeter 190-204/S

Fluke 200 MHz 2.5 GS/s (1.25 GS/s 4ch), 4 channel digital oscilloscope. Features Persistence mode, Connect-and-View triggering for intelligent, automatic triggering on fast slow and complex signals. 10,000 points per trace waveform capture (scope mode), USB host port for direct data storage, automatic capture and replay of 100 screens. Roll mode gives 30,000 points per channel for low frequency signal analysis, TrendPlot paperless recorder. Isolated inputs and safety rating CAT III 1000V / CAT IV 600V.

Fluke SMFT-1000 Solar I-V Curve Tracer Pro Kit

Fluke SMFT-1000 Solar I-V Curve Tracer Pro Kit for PV installation, commissioning, inspection, and maintenance testing that conforms to IEC 62446-1 standards. 1000V/20A, maximum power 20KW , supplied with Irradiance Meter and TruTest™ Advanced Solar Software.

Fluke Ti480 PRO Infrared Camera

Fluke Ti480 Pro thermal imaging camera, temperature range -10 to 1,000 degC, 640 x 480 thermal resolution (1280 x 960 with SuperResolution mode) and 0.93 mRad. Wireless connectivity to PC, Apple or Android. Image capture still or video with live streaming capabilities. MultiSharp focus provides image focus throughout the field of view and a built-in laser distance meter displays the distance from your target.

Fluke TiS75+ Thermal Imaging Camera

The Fluke TiS75+ camera has a 384 x 288 thermal resolution, features voice annotation, IR-PhotoNotes, and asset tagging. Additionally, it stores inspection notes and location information directly with the captured images for a proactive maintenance (PM) program. " Temperature range -20 to 550 degC " Manual focus " IR-Fusion

Fujikura FSM70R+ Ribbon Fusion Splicer Kit

Fujikura FSM70R+ ribbon fibre fusion splicer. Typically splice time 11 seconds and sleeve shrink time 29 seconds. Detachable work table and arc-free calibration system. Includes CT-50 cleaver and thermal jacket stripper.

Fujikura FSM70S+ Core Alignment Fusion Splicer and Cleaver

Fujikura FSM70S+ single fibre core alignment fusion splicer and CT50 cleaver. Typical splice losses of 0.02dB and 0.01dB on single and multimode fibre respectively. Automated tension test, wind and heater cover, 6 second Ultra Fast splice time, 14 second heat time and 20,000splicer result storage.

Futek IHH500 Pancake Load Cell 20T Capacity

The Futek IHH500 Display & LCF500-FSH02968 loadcell operate at up to 20 tonnes (50,000lb) in compression and tension. The IHH500 hand held display is a logging microcontroller which can store up to 21000 points, it is powered by a rechargeable battery which can last for up to 30 hours depending on battery condition and load. It will operate from its mains charger if needed. The system has a simple Tare function and can display Max Hold using a single front panel key. The lead that connects the loadcell to the display is 1.6 Meters long. The load is connected via M33x2-Threads. There are two eye bolts supplied with the system, however the eye bolt capacity is 7 ton. The software is supplied on a USB flash drive / dongle Please see the attached brochure for more detail and its other features.

Futek IHH500 Pancake Load Cell 2T capacity

The Futek IHH500 Display & LCF400-FSH03132 loadcell operate at up to 2 tonnes (5000lb) in compression and tension. The IHH500 hand held display is a logging microcontroller which can store up to 21000 points, it is powered by a rechargeable battery which can last for up to 30 hours depending on battery condition and load. It will operate from its mains charger if needed. The system has a simple Tare function and can display Max Hold using a single front panel key. The lead that connects the loadcell to the display is 1.6 Meters long. The load is connected via M12x1.75-Threads. The software is supplied on a USB flash drive / dongle

General Dynamics R8000B Communications Analyser

The General Dynamics R8000B (now produced by Freedom Communication Technologies) is a compact communication system analyser which is designed to monitor and service radio communications equipment. It also generates and receives signals and measures modulation and frequency. The R8000B performs a variety of tests on AM, FM, PM, and optional digital standards P25, DMR, NXDN, and TETRA radio transceivers. The R8000B is a full-featured instrument which acts as a spectrum analyser, signal generator, sensitive measurement receiver, oscilloscope, and much more. With high spectral purity, it is a lightweight and truly portable solution to effective communications system analysis. Features: • Frequency range 250 kHz to 1 GHz • 50 W 5 min, 150 W max • Less than 6.4 kg and has an 8.4" colour LCD screen • DANL is -140 dBm (50 Ohm input termination)

IET Resistance Temperature Detector Simulator RTD-250

IET Labs, Inc. RTD-250 RTD Simulator. 20 to 1,121.10 Ohm, 5 decades, accuracy (ppm) 200, resolution 10m Ohm.

Grant TX150 Temperature Bath

Water/oil bath and circulator for calibrating temperature probes and analytical procedures. Temperature ranges from ambient to 100 deg C with water and 150 deg C with silicon oil. Features include digital temperature controller and display, timer, alarms, offset adjustment and more. ISO/IEC 17025 certified.

Hagner EC1-X Lux Meter

Digital illuminance meter with NATA certification. measurees from 0.1~200,000 lux. Has a remote measurement head on 2m cord. Accuracy +/- 3% of range +/- last digit. Battery Operated.

Hilti PS1000 X-scan Concrete Scanner

Hilti PS1000 X-scan Concrete Scanner supplied with PLC 600 layout tablet. Locate rebars, tendons, metal and plastic conduits, glass-fibre cables, voids, and wood in dry concrete structures at depths of up to 300 mm(450mm with expert mode).. PLC 600 layout tablet suitable for 3d view and analysis on site.

Hioki Kit of Three 9322 High Voltage True rms Interface

Used with many memory recorders, eg. Hioki 8835. Operating modes 3. DC mode for waveform monitor output DC to 3MHz, AC mode detection of power surge noise 1kHz~10MHz. Rectified true RMS output of DC & ac voltages. 40Hz~100kHz response speed 200ms or less. Max voltage DC 2kV, ac 1kV CATII, AC/DC 600V CATIII, balanced differential input 1/1,000 divider.

Hioki 9694 Clamp-on CT 5A(set of 3)

Hioki 9694 5A CT - set of 3 suitable for PW3365-20

Hioki 9694 Clamp-on CT 5A (Set of 4)

Rated primary current 5A AC. Amplitude accuracy +/-0.5% rdg. +/-0.2% fs (at 45 to 66Hz), 66Hz to 5kHz +/-1% or less. Max circuit voltage 300V RMS/insulated wire. Core jaw 15mm diameter. Size mm: 46w x 21d x 135h, cord length 3m.

HIOKI BT3554-52 Battery Tester

Takes on-the-spot measurements of the internal resistance,and voltage of lead-acid batteries, for UPS and similar applications, without taking it offline. Instantaneous results and easy data management with mobile app( GENNECT Cross) or PC (GENNECT One). Up to 6,000 data sets can be saved. Pass, Warning, or Fail results using comparator function. Comes with Z3210 wireless adapter to communicate with smartphones or tablets via GENNECT Cross App.

Hioki CT7116 6A AC current sensor

CT7116 is a 6A AC Current Sensor suitable with Hioki PQ3198-94

Hioki CT7731 100A AC/DC with CM7291 display unit

Hioki CT7731-100A AC/DC with CM7291 display unit. Suitable with MR8847-53 and MR6000-01 loggers. Can also be used with HIO,PQ3198-94 without display unit

Hioki CT7742 2000A AC/DC with CM7291 display unit

Hioki CT7742 2000A AC/DC with CM7291 display unit. Suitable with MR8847-53 and MR6000-01 loggers. Can also be used with HIO,PQ3198-94 without display unit

Hioki 3532-50 5MHz LCR Meter

Hioki 3532-50 frequency range 42 Hz to 5 MHz. 5 ms high speed measurements. Basic accuracy of +/-0.08%. Memory for 30 sets of measurement conditions, including comparator values. Includes correlation correction function, interactive touch panel operation and enlarged display function. Applications include laboratory use for evaluation of operating characteristics, production line use or R&D. Measurement data captured by a personal computer can be displayed graphically by using standard spreadsheet software.

Hioki LR8431-20 10ch Memory Logger

Hioki LR8431-20 10 Channel Memory Logger with isolated channel to 60VDC which will take thermocouples. 10ms sampling USB interface and USB memory stick. Logging software included. Log directly to memory stick. Includes battery for 2.5hrs continuous operation.

Hioki MR6000-01 8 Analogue, 16 logic channel Memory Recorder

High Speed Memory Recorder 20MSample 8 channels 12bit Max. rated voltage to earth: 300 V AC, DC,16 logic channels with voltage detection probes 150V or 15V threshold . Touch screen display with PC rem ote operation.

Hioki MR8847-53 8 Analogue, 32 logic channel Memory Recorder

Hioki MR8847-53 Memory recorder with 8 analogue and 16 logic channels (16 logic probes supplied). High-speed 20MS/s,Fully Isolated Memory recorder. Analog unit 8966 has Max. rated voltage to ground: 300 V AC, DC

High Voltage Inc PFT-1003CMF 100kV AC Hipot Test Set

Portable (16kg control unit, 39kg HV tank) hipot tester, 100kV, 50Hz, rated 3kVA into capacitive loads. Features continuously adjustable output voltage, external safety interlock, zero start safety interlock, self resetting over current protection, guard/ground return mode, HV on/off and main power pushbuttons and ruggedized meters with glass windows that eliminate static buildup.

High Voltage Inc PFT301 30kV AC Hipot Tester

The PFT301CM is a portable HiPot 0~30kVac 1kVA resistive/capacitive load: 33mA. Duty cycle at 1kVA 1h on 1h off 700VA Continuous. Tests the integrity of items including insulating materials, isophase bus duct, switchgear, transformers, vacuum bottles & interrupters, vacuum switches, automatic circuit reclosers, bushings, fuses, arrestors, circuit breakers, transformers, capacitors, motor and generator windings.

High Voltage Inc PFT-503CM 50kV AC Hipot Test Set

Single, portable (34kg) unit suited for testing overhead apparatus, vacuum bottles and interrupters, switch gear, bus duct, motorized vacuum switches, reclosers, bushings, fuses and arrestors, linemans safety products, small transformers, electrical components and motors. This 3kVA model features capacitive load compensation enabling full load testing with a power draw of 1.5kVA while operating from a conventional line input. 60mA output current capability.

Holaday HI-3604 E & H Survey Meter ELF

Low frequency field meter. Designed to evaluate electric and magnetic fields associated with 50Hz power lines. Frequency range 30 - 2,000Hz. Measures magnetic fields from 0.1 milligauss to 20 gauss. Measures electric fields from 1 volt/meter to 200 kilovolts/meter. LCD display. 127 reading data memory.

HPI Cypher 5000 Digital Radiation Alert Monitor

Alpha, Beta, Gamma and X-ray radiation monitor. Meter, LED, audible indication and detachable probe. Range 0.1 to 1,000,000 CPM; Accuracy 1% or 2 digits.

HV Diagnostics HVA30 30kV VLF/DC Test Set

VLF and DC test capabilities combined in one unit (20 kg). Suitable for testing cables (XLPE, PE, EPR, PILC etc), capacitors, switchgear, transformers, machines (IEEE 433), insulators and bushings. VLF (0.1Hz to 0.02Hz), DC (+/-), cable fault conditioning (burning) and sheath/jacket testing modes all included. Fully automatic or manual cable test sequences complying with International Standards/Guides such as IEEE 400.2, VDE 0276 and CENELEC. True symmetrical sinusoidal, load independent, output waveform across the full load range. Real-time display of actual output wave form. Easy to use, ergonomic, menu guided, large backlit user interface. Large output load capability (up to 5uF). Automatic and integrated load capacitance measurement with optimum frequency selection. Storage of test results for later retrieval or download to a PC/Laptop.

HV Diagnostics HVA60 60kV VLF/DC Test Set

VLF and DC test capabilities combined in one unit (60 kg). Suitable for testing cables, capacitors, switchgear, transformers, machines, insulators and bushings. VLF (0.1Hz to 0.02Hz), DC (+/-), cable fault conditioning (burning) and sheath/jacket testing modes all included. Fully automatic or manual cable test sequences. True symmetrical sinusoidal, load independent, output waveform across the full load range. Real-time display of actual output wave form. Large output load capability (up to 5uF). Automatic and integrated load capacitance measurement with optimum frequency selection. Storage of test results for later retrieval or download to a PC/Laptop. For a more comprehensive understanding of insulation condition perform tan delta testing at the same time with optional accessory HVD,HVA TD60.

HV Diagnostics/B2HV HVA94 94kV VLF Test Set

VLF, DC and Jacket/Sheath testing. Sinusoidal: 0 - 94 kV peak, 0 - 66 kV rms DC: ± 0 - 90 kV and Squarewave: 90 kV. The high power HVA94 Test System is capable of testing cables up to 3,300 m - 1 µF at 0.1 Hz and 61 kV rms, 0.85 µF at 0.1 Hz and 66 kV rms. The variable output frequency allows the testing of even much longer cables. 0.01 … 0.1 Hz in steps of 0.01 Hz (default 0.1 Hz) - auto frequency selection. Stores 50 test records.

Inno View 8X Core Alignment Fusion Splicer and Cleaver

Inno View 8X single fibre core alignment fusion splicer and V12 cleaver. " 0.01dB typical splice loss SM & MM. " 4 second average quick mode splice time. " 9 second quick heat time. " 20,000 splice data and 10,000 splice image results storage.

IONSCIENCE Gascheck Helium,butane & SF6 detector

Microthermal conductivity gas leak detector. Reading in cc/sec, g/yr, mg/m3 or ppm. Detects most gases however particularly suited to ammonia, argon, butane, helium, hydrogen & SF6. Calibrated against Helium. Battery Life 40h. Sensitivity (cc/sec) He 1x10-5, CH4 5x10-5, R12 5x10-5, Ar 1x10-4. Accuracy 5% of displayed reading + 1 digit. Response 1s. Flowrate 2cc/min. Operating -20~60DegC.

Jofra CTC-1205A Dry Block Temperature Calibrator 1200 C

NATA calibrated Jofra CTC-1205A dry well temperature calibrator. Range 100 to 1,205 degC. Accuracy +/- 2 degC, stability +/-0.1 degC. Immersion depth 110mm (with insulation plug 137mm). Supplied with insert with hole sizes 3.5, 5, 7 and 10mm.

Jofra CTC-660A Dry Block Temperature Calibrator 28 to 660 C

Jofra CTC-660A Dry Block Temperature with NATA certification. Range 28 to 660 degC. Accuracy +/-0.85 degC, stability +/-0.08 degC and resolution of 0.01, 0.1 or 1 deg. Immersion depth 115mm. Supplied with insert M01 (hole sizes, 9, 5, 6, 4, 4, 3mm). Various insert sizes available, please inquire.

Jofra CTC-660A Insert

Various insert sizes for the Jofra CTC-660A (only). Please inquire.

JOF,RTC-157A Insert

Insert for the Jofra RTC-157A (only). Please inquire.

Keysight 33612A Waveform Generator, 80 MHz, 2-Channel

Keysight 33612A, 80 MHz, 2 channel waveform generator, sine, square, pulse, ramp, triangle, Gaussian noise, PRBS and arbitrary waveforms. Capable of modulation, sweep, burst, waveform summing and combining. Maximum output into 50 ohm, 1 mVpp to 10Vpp. Up to 120 MHz sine and Gaussian noise at <= 4 Vpp. Memory is 4 MSamples deep

Keysight DSOX3024A Oscilloscope 200 MHz, 4 Channels

Keysight 4 channel 200MHz digital storage oscilloscope. Sampling rate 2 G/s (4 G/s half-channel interleaved mode). 2Mpts memory depth, waveform update rate 1 million waveforms/s, sensitivity 1mV/div to 5V/div. Pass/fail masks can be automatically created based on an input reference waveform or on a PC then imported via USB, also store and remove waveforms via USB.

Keysight MSO6104A 1GHz Digital Oscilloscope with Logic

Keysight 1GHz 4 + 16 channel mixed signal oscilloscope (MSO). 4Gsa/s. XGA Colour display updates 100,000 waveforms/s with 256 levels intensity. 4 analogue channels and 16 logic channels. Deep memory, 8 digit frequency counter function. Triggering includes video, HDTV, I2C, SPI, LIN, CAN, & USB. FFT analysis included. LAN, USB, GPIB, & XGA interfaces standard. NATA certified.

Keysight N9344C 20GHz Spectrum Analyser with GPS

Agilent/Keysight N9344C spectrum analyser 9kHz to 20GHz with GPS. -144dBm displayed average noise level (DANL), <0.95s sweep time for 20GHz full span. Average continuous power, +30dBm for 3 minutes maximum. Flexible remote control via USB/LAN. User memory 64MB, able to store approximately 14,000 traces.

Keysight N9344C-TG 20GHz Spectrum Analyzer/Tracking Generator

Agilent/Keysight N9344C spectrum analyser 9kHz to 20GHz with 5MHz to 7GHz tracking generator. -144dBm displayed average noise level (DANL), <0.95s sweep time for 20GHz full span. Average continuous power, +30dBm for 3 minutes maximum. Flexible remote control via USB/LAN. User memory 64MB, able to store approximately 14,000 traces.

Kikusui TOS5101 10kV AC/DC Hipot Tester

Hipot testing up to 10kV in either DC or AC. Digital voltmeter and ammeter, digital timer. Window comparator for more reliable pass/fail judgement. Automatic discharge of DUT in DC test mode. Equipped with Key Lock and Interlock functions for greater safety.

Kingfisher KI-28010 Single Mode APC LS and KI-2600 PM

Kingfisher singlemode light source KI-28010 and power meter KI-2600. Compatible with APC and PC singlemode networks. Wavelengths 1310, 1550 and 1625nm. Memory with text, timestamp and USB dump, real-time PC reporting software. Autotest provides fast, easy and automatic multi wavelength loss testing.

Leica BLK360 G2 Laser Scanner

The Leica BLK360 G2 is an advanced precision imaging laser scanner. At the push of a button, users can capture a full scan with spherical images in only twenty seconds-over five times faster than the original BLK360. The VIS technology automatically combines your scans on-site to speed up your workflow and help you make sure your datasets are complete. BLK360 data is valuable for many uses, from traditional AEC, to mind-bending VFX and VR. Users can easily transfer and work with it in their software ecosystem to create immersive and highly accurate deliverables and experiences. Features: • Capture data up to 680,000 points per second • Rich high dynamic range (HDR) imagery. • Small and light, weighing just 850 g with batteries. • 5 times faster than the original BLK360. • 20 seconds for a full-dome scan with photospheres. • Visual Inertial System (VIS) automatically pre-registers scans in the field. • High speed data transfer via USB-C and WiFi.

Leica GS18 UHF Base Kit

The Leica GS18 is a self-learning GNSS smart antenna. GS18 inherits all features of the Leica GS18 T except tilt compensation. The GS18 is an excellent companion to a surveyor that primarily works with a network RTK such as HxGN SmartNet. Like most of the Leica Geosystems GNSS smart antennas, the GS18 works as a rover and a base.

Leica GS18 Network Rover with Controller

The Leica GS18 is a compact and self-learning GNSS smart antenna. Featuring Leica's RTKplus GNSS engine, this receiver is able to be more selective about what signal it uses and intelligently adapts to changing conditions by selecting the optimal signals to deliver the most accurate positions. Paired with Leica's SmartCheck RTK quality control, the GS18 offers some of the highest standards in GNSS measurement. The GS18 rover kit includes a CS20 controller running Leica Captivate software and rangepole.

Leica ICG160T Network Rover with Controller

Building upon the previous ICG-60, the ICG-160 rover introduces IMU tilt compensation and a larger onboard control panel for easier everyday use. Supplied with a CC200 Toughpad tablet and pole. Requires either an onsite GNSS base or network RTK coverage (RTK access provided).

Leica RTC360 Laser Scanner

The Leica RTC360 3D reality capture solution is simply the fastest, most productive and most powerful laser scanner on the market. Highly portable, highly automated, intuitive and designed for maximum productivity. Use the included iPad to automatically record your moves from station to station to pre-register your scans in the field without manual intervention. Features: • Capture 2 million points per second • Full Dome HDR imagery in 1 minute • Full High Res scans in less than 2 minutes • Vis, inertial, compass, altimeter and GPS sensors

Leica Traverse Kit with 2 Targets

The Leica Traverse Kit can be used with the Leica Robotic Total Stations for use as a backsight or for precise traversing. Features " Matches the height of the Leica Instruments " Easy backsights or false centre traversing " Contains 2 x Targets, laser plummets in a single carry case " Provided with 1 or 2 Heavy Duty Tripods if needed

Leica TS16 1sec Robotic Total Station

The Leica TS16 sets the benchmark for robotic total stations. It offers consistent performance for general purpose land surveying and stakeout, as well as more specialised infrastructure work. PowerSearch and ATRPlus technology enables fast prism acquisition at the press of a button.

Leica TS16 1sec Robotic TS with Controller

The Leica TS16 is benchmark for surveying accuracy. Whether you want to stake-out an object on a construction site, need accurate measurements of a tunnel or a bridge, or survey a parcel of land - you need reliable and precise data. Automatically adjusting to any environmental conditions, the Leica Viva TS16 locks onto your, and only your, target. Features " The latest CS20 controller with Leica Captivate " Powersearch for finding your prism easily " Reflectorless range greater than 500m " 1 second angular accuracy

Madgetech 5g Transient Shock Transport Logger

MadgeTech TSR101-EB-5 Transport logger. This device includes a 5g triaxial Accelerometer. The extended battery option gives a 30day battery life. It also includes the magnetic mount kit. It records detail of all shocks above a user selectable threshold at from 1Hz to 1024Hz. It has a total of 340k measurements per axis. Resolution .01g Accuracy 0.2g

Mecmesin AFG-1000NALC Force Gauge

Range 0~1000N accuracy 0.1%. 5 digit back lit display. Peak data sampling rate 5kHz. 120% overload warning, display invert (reverse) function, dual max, max tension & max compression plus current reading. Outputs: analogue, RS232 & Mitutoyo. Accessories: test hook, compression plate, 30mm extension rod, rotary coupling. Mounting tapped holes x 2, M5 x 0.8 x 5.5mm deep max. Optional smart sensors can be used, such as TW60 static torque wrench.

Megger BVM300 battery voltage monitor

BVM300(System of 31 BVM units) which is a 0~5VDC and 0~20VDC 1mv resolution .1% accuracy daisy chained 31 channel voltage datalogger. This integrates with the Torkel controller to give cell by cell voltage measurement. This means if the battery string fails a load test the individual battery that is the culprit can be easily identified. These two instruments combineed together meet the test standards IEEE450, IEC896-1, IEEE 1188-1996 & IEC896-2.

Megger DCM1500S Solar/PV Clamp meter

DCM1500S Solar PV Clamp Meter measures up to 2000V DC and 1500V AC (using the PVHV Leads), and 1500A AC or DC. Ideal for use in the installation, maintenance, monitoring and testing of photovoltaic systems and standard AC or DC electrical equipment. Supplied with standard 4mm leads, PVHV1 (4 mm) and PVHV2 (MC4PV) HV lead sets.

Megger DET2/3 Earth Tester

DET2/3 Earth Tester with ETK50C kit. High resolution of 1 mO, ideal for large earth (ground) systems. High accuracy for earth (ground) electrode grid and soil resistivity tests.Test in accordance with BS 7430 (earthing / grounding), BS-EN-62305 (Lightning Protection), IEEE Standard 81 and Railway Applications

Megger DLRO lead set Current & Voltage leads

For Megger DLRO digital micro-ohm meters, potential spike lead set 2 x 2m long & current clip lead set 2 x 2m. These are used to separate the C & P connections which avoids the erroneously high readings taken due to a high resistance contact.

Megger DLRO100XB 100A Micro-Ohm Meter

Megger DLRO100XB - 100A lightweight, mains and battery operated digital low resistance ohmmeter. Unit is supplied with 5m kelvin lead set and DC clamp. Measurement range from 0.1 micro-ohm to 1.999 ohm with resolution 0.1 micro-ohm. Applications include testing switchgear and circuit breaker contact resistance, busbar and cable joints, wire and cable resistance, bond testing in various industries like utilities, manufacturing, transport and aviation.

Megger DLRO10HDX Micro-ohmmeter

Simple rotary switch selection of five test modes, including auto start on connection.The unit is powered from either its rechargeable battery or mains. Capable of delivering 10 A into measurements up to 250 mohm and 1 A into measurements up to 2.5ohm. The duration of each test may be up to 60 seconds. Memory storage for test results up to 200 records Applications ranging from railways and aircraft to resistance of components in industry.

Megger DLRO10X Microhmmeter

Self contained fully automatic (with manual option) micro-Ohmmeter, selecting the most suitable test current up to 10Adc. Range 0.1micro-Ohm to 2kOhm, resolution 0.1micro-Ohm. Internal memory for 700 tests. Download software supplied. RS232 communications to PC. LCD display. Rechargeable battery.

Megger DLRO200 200A Micro-Ohm Meter

The Megger DLRO200 is a digital low resistance ohmmeter that measures resistances between 0.1 micro-Ohm and 1 Ohm ? at high currents. It is used to test circuit breaker and switch contacts, busbar joints, and other applications where high current is needed. The DLRO200 can operate in three modes. In continuous mode it will monitor a resistance over a period of time. In normal mode it will test a current at the push of a button. In auto mode, once the desired current is selected and leads are connected, it will start testing, which is a handy mode for testing busbar joints. Features: • Provides test currents from 10 A to 200 A dc • Includes 5 m Lead set with 2 x 50 mm ² current leads and 2 x potential leads (with clips) • On board memory for up to 300 test results and notes • RS232 port to download stored results or for real time output to a printer

Megger DLRO 600 Digital Micro-ohmmeter - High Current

Test current range 10A to 600Adc. Measurement range 0.1uohm to 1ohm, resolution 0.1uohm. Current cables 2x5m. Internal memory for 300 tests. Download software supplied. RS232 communications to PC. LCD display.

Megger EZ-Thump 12kV Thumper & TDR Power Cable Fault locate

The Megger EZ-Thump is a compact and light weight portable cable fault locations system which is also suitable for This unit incorporates a 12 kV Hipot tester, time domain reflectometer (TDR), and surge generator. It can be powered from an ac supply or internal batteries (3 h recharge time provides 30 m of thumping). Surge generator produces a 500 J, 0 to 12 kV at 12 mA pulse. The kit includes the Digiphone Plus pin-pointer with surge wave receiver to locate faults while thumping.

Megger Ingvar Primary Current Injection Test System

Primary injection testing system consists of a Control Unit and a Current Unit. Up to 1600A output current with cables supplied. Unit is capable of up to 5000A output current with special cables(not supplied). Suitable for switchgear and CT commissioning, ground grid, circuit breaker testing and more

Megger MIT1025 10kV Tester

The Megger MIT1025 is a 10 kV Insulation Resistance Tester (IRT) capable of resistance measurements up to 20 Tohm. Testing options include Polarisation Index (PI), Dielectric Absorption Ratio (DAR), Dielectric Discharge (DD), Stepped Voltage (SV) and ramp test. The unit has a CATIV 600 V safety rating and dedicated voltmeter function (30 V to 660 V). The MIT1025 IRT also features a rapid charge Li-ion battery with the ability to take measurements on a flat battery when connected to mains power. Features: • Noise filter - rejects up to 3 mA noise • Advanced memory includes time/date stamping of results • High altitude operation up to 3000 m • PowerDB Lite software for download of test data to PC

Megger MIT525 5kV Insulation Tester

5kV DC Insulation Resistance Tester. Measures to 20 Tohm at 5kV. Tests include PI, DAR, DD, SV and ramp test. Li-ion battery with rapid charge, mains operation possible while battery is charging. Advanced memory with date/time stamp. Noise filter rejects up to 3 mA noise. PowerDB Lite asset management software supplied with unit for download of test data to a PC.

Megger MOM3 Microohmmeter

The Megger MOM3 Handheld Micro-Ohmmeter is a precision instrument designed for low resistance measurement in electrical systems, making it ideal for testing circuit breaker contacts, busbar joints, and other high-current links. Its compact, battery-powered design allows for convenient field use, while delivering accurate and repeatable results even in demanding environments. Engineered for technical professionals, the MOM3 utilises advanced measurement technology to provide reliable readings down to micro-ohm levels. The instrument features a user-friendly interface, robust construction, and is optimised for both portability and performance. For detailed technical specifications, refer to the technical specifications. Key Features: High Measurement Accuracy: Measures resistance from 0.1 micro-ohm to 3000 milli-ohm with high precision, suitable for critical low-resistance applications. Powerful Test Current: Delivers up to 300 A DC test current, ensuring reliable contact resistance measurements in high-current components. Battery Operated: Fully portable with rechargeable battery operation, enabling use in remote or field locations without external power. Lightweight and Compact: Weighs only 1.15 kg, designed for easy transport and single-handed operation in tight spaces. Digital Display: Large, clear digital readout for easy interpretation of measurement results in real time. (High contrast backlit display) Data Storage: Internal memory for storing up over 2000 test results, facilitating efficient data management and reporting. The Megger MOM3 Handheld Micro-Ohmmeter is a robust and efficient solution for professionals requiring accurate low-resistance measurements in the field. Its technical capabilities and portable design make it a valuable tool for maintenance, commissioning, and troubleshooting of electrical systems.

Megger OTS80PB Transformer Oil Tester

Test voltage 80kV max at 61.8Hz. Fully automatic operation. Rechargeable batteries. RS232C interface.

Megger PAT420 Testing and Tagging System

Megger PAT420 portable Appliance Tester. Tests to AS3760. Stores data on USB memory stick. includes a barcode scanner and label printer.

Megger RCDT330 Residual Current Device Tester

Tests standard, DC, selection and programmable RCDs. Ramp testing. Auto (remote) testing. 3ph safe. Enables testing on 110V centre tapped supplies. Performs 1/2I, 1xI & 50xI tests on RCDs rated at 10mA, 30mA, 100mA, 300mA, 500mA & 1000mA on general and selective (time delayed) RCDs. Weatherproof to IP54.

Megger TDR2000-3P Dual Channel TDR Cable Fault Locator

Time Domain Reflectometer cable fault locator. User selectable ranges from 0 to 50m up to 20km, minimum resolution 0.1m. Dual cursor measurement. Internal memory for 15 traces. Megger "Tracemaster" software supplied. High resolution LCD display. Battery powered. Dust and shower proof to IP54. This system can operate on live cables.

Megger Torkel 950 battery discharge tester

Battery discharge load unit. Works with 7.5V to 500V battery systems and can discharge at up to 220A (15kW maximum power). It can be programmed for constant current, constant power, constant resistance or user defined load profiles. The kit includes a 200ADC current clamp allows on-load testing. Tests are controlled by a built in PC and results can be copied to a USB memory stick.

Megger TXL870 Extra Load Unit

Optional accessory for the Megger Torkel 950 battery discharge tester. Adds up to an extra 112A load capacity to a discharge test (15.8kW maximum). Operates as a slave in combination with Megger Torkel 950 battery discharge tester.

MEGGER VIDAR Vacuum Circuit Breaker/Interrupter Tester

Megger Vidar checks the integrity of vacuum interrupter/ circuit breaker. User defined voltage selection, with extensive voltage range. Follows ANSI/IEEE standardized DC test methods. A suitable test voltage (DC) is applied to breaker, for PASS/FAIL results.

Metrel A-1532 EVSE Adapter

A 1532 EVSE XA adapter is an EV Charging station tester used for verification of electrical safety and functional testing of EVSE together with MET,INSTALTEST-XD.

Metrel Instaltest-XD multifunction tester

Metrel Instaltest-XD multifunction installation tester provides electrical safety and functional testing of electrical installations. Supplied with MESM software.

Metrel MI3115 PV Analyzer

MI3115 PV Analyzer offers testing in accordance with the IEC 62446 standard and supports all category 1 and category 2 tests and measurements. Tests include insulation resistance measurements of PV strings, I/U characteristic measurements, and the conversion of measured values to STC values and comparison with nominal values given by the PV modules manufacturers. The irradiation and cell temperature are measured in real time with the wireless remote unit.

Metrel MI 3116 Solar PV Analyser XA

The Metrel MI 3116 Solar PV Analyser XA is a cutting-edge solution designed for comprehensive testing, commissioning, and troubleshooting of photovoltaic (PV) installations. Ideal for solar professionals, this advanced analyser (1500V/ 40 A) streamlines the process of verifying PV system performance, ensuring safety, and maintaining compliance with industry standards. Whether you need to rent or hire a reliable solar PV analyser for installation, maintenance, or diagnostic tasks, the Metrel MI 3116 delivers precise results and robust functionality. Manufactured by Metrel, a leader in electrical measurement technology, the MI 3116 Solar PV Analyser XA offers a complete suite of tests for both DC and AC sides of PV systems. It measures I-V curves, insulation resistance, earth continuity, and voltage. With intuitive operation, high-resolution display, and advanced data logging, this analyser is engineered for professionals who demand accuracy and efficiency in solar PV system assessment. Its portable design and robust construction make it suitable for both field and laboratory environments, enhancing productivity and reliability in every project. Key Features: Comprehensive PV Testing: Performs I-V curve tracing, insulation resistance, and earth continuity tests for complete PV system analysis. High-Resolution Display: Large, clear screen for easy data interpretation and on-site diagnostics. Advanced Data Logging: Stores test results for later review, reporting, and compliance documentation. Rugged, Portable Design: Built for demanding field conditions with a lightweight, ergonomic form factor. User-Friendly Interface: Intuitive menu navigation and quick setup for efficient workflow and reduced testing time. Why Choose the Metrel MI 3116 Solar PV Analyser XA? Delivers highly accurate and reliable PV system diagnostics. Supports a wide range of solar installation testing requirements. Streamlines workflow with efficient, easy-to-use features. TechRentals provides the Metrel MI 3116 Solar PV Analyser XA on flexible rental terms, giving you access to premium equipment without the upfront cost of ownership. Backed by over 50 years of industry expertise, we help ensure accurate and efficient solar PV system assessments. Enquire today to rent the Metrel MI 3116 Solar PV Analyser XA and streamline your solar PV testing and commissioning tasks. Not sure which equipment to hire? Call our friendly experts today and get the right solution for your project.

Metrel MI3309BT DeltaGT Portable Appliance Tester

Portable Appliance Tester. Battery and mains operated. Functional and visual inspection; Earth bond resistance; Insulation resistance; Insulation resistance of isolated accessible conductive parts; Substitute leakage current; Substitute leakage current of isolated accessible conductive parts; Differential leakage current test; Touch leakage test; RCD and portable RCD testing, type (K, S); Power test; IEC cord polarity test; Leakage and load currents with current clamp; TRMS voltage meter; Enhanced TRMS test. light weight and portable.

Mitutoyo Pro360 Digital Protractor model 950-317

Digital Protractors to measure inclination values on an easy-to-read LCD. Measurements are generated by an electronic gravity sensor. Full 360° range (90° x 4). Alternate reference (zero), Reading hold. Display remains upright to view at all angles. (950-317, Pro 360 Model). Accuracy: ±0.1deg Level ±10 deg, Plumb ±10 deg, ±0.2 deg Maximum error, Repeatability: ±0.1 deg and Resolution: 0.1 deg

Monarch PLT200-KIT Digital Contact/Non Contact Tacho

Hand held digital contact/non contact tacho kit. Ranges optical/non contact 5~200,000 RPM, contact 0.5~20,000 RPM. Display 5 digits, 5 alpha numeric LCD. Non contact operating range 90cm, tripod mounting. Direct contact tips and contact wheel supplied. Programmable for IPM, FT/M, YPM, cm/M, m/M, RPM, RPS, RPH and Totaliser up to 200,000. Output TTL pulse.

Narda NBM-550 E Field Strength Meter and Probe EF1891

The Narda NBM-550 Broadband Field Meter measures the field strength of non-ionising radiation from various transmission facilities. This includes mobile phone and broadcast towers, to determine radiation exposure to nearby workers and the general public. The Narda NBM-550 can be used to make precise measurements to establish human safety, particularly in workplace environments where high electric field strengths are likely to occur. It also includes a non-directional isotropic probe for applications in the frequency range 3 MHz to 18 GHz, with a probe interface that automatically detects probe parameters for simple operation. Features: • Large graphical display • GPS interface with automatic storage of position and measurement data • Built-in memory stores up to 5000 measurement results • Audible warning with programmable alarm threshold

Narda RadMan 2XT ICNIRP 1998 / Occupational

Narda Radman 2XT (2281/101) personal occupational limit monitor and leakage detector for monitoring RF signals in mobile, telecom, broadcast and industrial applications. Easy to use: • 5G Ready • Mounting adaptor for harnesses with safety lanyard • Integrated automatic sensor test • Highly visible alarm LEDs, loud buzzer plus vibration alarm • 800 hours of operation on a single charge Compliant: • Wide frequency monitoring up to 60 GHz • ICNIRP compliant for frequencies 900 kHz to 60 GHz • ICNIRP 2020 compliant for frequencies above 27 MHz • Detection of short pulsed signals • Data logger for permanent recording

NetAlly Etherscope EXG-300 Network Expert

The EtherScope nXG-300 Portable Network Expert is a multi-technology, all-in-one handheld network analyzer that enables engineers and technicians to deploy, maintain and document Wi-Fi and Ethernet access networks. Supports MultiGig networks from 10/100/1000Mbps to 2.5/5/10G and 802.11a/b/g/n/ac/ax. Also known as, Wi-Fi versions 1, 2, 3, 4, 5, 6/6E.

NetAlly LinkRunner 10G Ethernet Tester

LinkRunner 10G simplifies testing and configuration of copper and fiber Ethernet networks, streamlining workflows by combining essential functions of installation, triage, network validation and troubleshooting through layers 1-7. The LR-10G accelerates deployments, speeds up problem identification, and improves the efficiency and effectiveness of network installers and operations teams. Features: • LANBERT, Qualify premise cabling for carrying Multi-Gig and 10Gig Ethernet (requires LR-10G or EXG-300 at end point) • Layer 1-7 AutoTest enables any technician to find network problems • Monitor networks for intermittent issues, every minute for up to 24 hours • Validate up to 90W 802.3bt PSE with TruePower loaded PoE test

Omicron Arc 256X arc flash initiator

Omicron ARC 256x Arc Flash Initiator. This is a CMC accessory designed to simulate an arc using a xenon tube, This CMC accessory It has a 6 m (19.7 ft) long connection cable it is connected to the external interface socket of the CMC test set, which provides both the supply voltage as well as the signal that will trigger the flash.

OMICRON C-Probe 1 Clamp-on CT AC/DC

Optional accessory for OMI,CMC356 & OMI,CMC356_61850. C-Probe 1 is an active AC and DC current probe with voltage output. It is the recommended accessory for measuring currents with the CMC 356. It has 10A and 80A measuring ranges, frequency range DC to 10kHz. Accuracy error < 2% for currents up to 40A and frequencies up to 1kHz. Phase error < 0.5O @ 50/60Hz. Length 230mm. Output: 0-10A range 100mV/A, 0-80A range 10mV/A.

Omicron Cibano 500 circuit breaker test system

Cibano 500 with advanced package circuit breaker tester for medium and high voltage circuit breakers. Suitable for Timing tests, Static contact resistance test and Dynamic contact resistance test. Supplied with Primary Test Manager Software ideal tool for the diagnostic testing and condition assessment of circuit breakers.

OMICRON CMC 356 Advanced Protection Relay Test Set

Protection relay test set with six current sources (6 x 32A/430VA, 3 x 64A/860VA or 1 x 128A/1000VA), four voltage outputs (4 x 300V or 1 x 600V), 4 x binary outputs, 10 x multifunctional binary inputs (dry/wet) and Generator Combination Cable for wiring convenience. The six current and four voltage output channels are continuously and independently adjustable in amplitude, phase and frequency. All outputs overload and short-circuit proof. Laptop included, preloaded with Test Universe software (Advanced Protection + Transducer). Optional accessories: OMI,CMA156-6PCA OMI,C-PROBE1 OMI,CMGPS

OMICRON CMC 356 Advanced Protection Relay Test Set +61850

Protection relay test set with six current sources (6 x 32A/430VA, 3 x 64A/860VA or 1 x 128A/1000VA), four voltage outputs (4 x 300V or 1 x 600V), 4 x binary outputs, 10 x multifunctional binary inputs (dry/wet) and Generator Combination Cable for wiring convenience. The six current and four voltage output channels are continuously and independently adjustable in amplitude, phase and frequency. All outputs overload and short-circuit proof. Includes IEC61850 software package (GOOSE, Sampled Values, IEDScout, SVScout). ELT-1 and LLO-2 options not included. Laptop included, preloaded with Test Universe software (Advanced Protection + Transducer) and IEC61850 package. Optional accessories: OMI,CMA156-6PCA OMI,C-PROBE1 OMI,CMGPS

OMICRON CMC 356 Enhanced Protection Relay Test Set

Protection relay test set with six current sources (6 x 32A/430VA, 3 x 64A/860VA or 1 x 128A/1000VA), four voltage outputs (4 x 300V or 1 x 600V), 4 x binary outputs, 10 x multifunctional binary inputs (dry/wet) and Generator Combination Cable for wiring convenience. The six current and four voltage output channels are continuously and independently adjustable in amplitude, phase and frequency. All outputs overload and short-circuit proof. Laptop included, preloaded with Test Universe software Enhanced protection package.

Omicron CMC 500 Enhanced Protection Relay Test System

The OMI CMC500 (USH-3ADS) is a high-performance relay test set designed for three-phase protection testing and secondary injection applications. With exceptional output accuracy, it offers up to 10 current and 7 voltage channels, plus both wet/dry binary and analogue inputs - including DC measurement capability. Ideal for advanced electrical testing, the standard configuration includes the NET-3 communication interface, precision timing features, and a laptop with pre-installed Test Universe software (Enhanced Protection Package) for streamlined operation. Flexible output options: - Multi-phase current: 7× 30A + 3×60A; 6×60A; 3×120A - Single-phase current: 1×360A - Voltage: 7× 300V TechRentals offers premium equipment for flexible rental terms - enquire today to support your power systems testing needs with confidence and precision.

Omicron GPS time reference

Omicron CMGPS588 synchronization unit is an antenna-integrated GPS controlled time reference. It is optimized for outdoor usage and works as a grandmaster clock according to IEEE 1588-2008 / IEEE C37.238-2011 Power Profile.

Omicron COMPANO 100

Battery Powered Primary injection, secondary injection, and basic protection test set. Applications include Wiring and polarity checks, Burden measurements, Single-phase protection relay testing, CT / VT ratio checks, Micro-ohm resistance testing. 150 V AC / 220 V DC output (30 VA), 110 A AC / 100 A DC output (600 VA) and Inputs binary wet/dry, AC/DC voltage 300 V or current with shunt. Supplied with Wiring check add-on and Grounding system. Optional HGT1 and HGT1 with PTM software available for step and touch voltages measurement.

Omicron CP CR600 Compensating reactor

CP CR600 is a compensating reactor for the CP TD12 and TD15.Allows testing of the insulation quality of generators, motors and other systems with high capacitances up to 1 µF at rated frequency. Used with CPC 100 + CP TD12/15 for dissipation factor (tan delta) and power factor measurements.

OMICRON CP TD12 Capacitance and Tan Delta add-on

CP TD12 is accessory for CPC 100 for performing power/dissipation factor and capacitance measurements. Suitable to determine a wide range of electric and dielectric parameters: Power factor, dissipation factor (tan d),Capacitance, Exciting current, Watts / power (P, Q, S), Inductance, Impedance, Current, Phase angle, Quality factor

OMICRON CP TD15 Capacitance and Tan Delta add-on

CP TD15 is an accessory for CPC 100 for performing power/dissipation factor and capacitance measurements 15KV. Suitable to determine a wide range of electric and dielectric parameters: Power factor, dissipation factor (tan d),Capacitance, Exciting current, Watts / power (P, Q, S), Inductance, Impedance, Current, Phase angle, Quality factor

Omicron CPC100 Multi-Functional Primary Test System

Portable (29 kg) primary test system suited for testing of current transformers, voltage transformers, power transformers, power lines, HV cables, grounding systems, switchgear and circuit breakers, protection relays and more. Tests to 800A over frequency range 15Hz to 400Hz, or to 400A DC. Laptop included, preloaded with CPC 100 Toolset and PTM software. Optional accessories: OMI,CPCU1 (with or without OMI,HGT1) OMI,CPSB1 OMI,CP-TD12/TD15, OMI,CP-CR600

Omicron CP CB2 Current Booster

OMICRON CP CU1 Multi-purpose coupling unit for CPC 100

Combined with the CPC 100, the CP CU1 is a measurement system for line impedances & k-factors of overhead lines or power cables, mutual coupling of parallel lines, ground impedances of large substations and coupling of power lines into signal cables. This test system overcomes the problem of power system frequency interference that has previously made it necessary to use extremely large, high-power equipment to carry out these measurements.

Omicron CPSB1 Switch Box

Switch Box to allow fully automated 3 phase transformer testing, accessory for the CPC100. Requires CPC100 with DEMAG option

OMICRON CT Analyser Current Transformer

The Omicron CT Analyser tests protection and metering CTs according to IEEE and IEC standards. It will measure phase-angle, ratio, winding resistance, excitation/saturation, and burden impedance. Results of the assessment are received as a "pass or fail" decision within seconds due to the automated testing process. Features: • Field verification up to the 0.1 accuracy class • Compact and lightweight (< 8 kg) • High noise immunity for on-site testing

Omicron SB2 Switch box for CT Analyzer

CT SB2 switch box is an accessory for the CT Analyzer which allows automatic testing of multi-ratio current transformers. Up to six connections for the secondary side of the current transformer

Omicron Dirana Transformer Insulation Moisture Analyzer

The OMICRON DIRANA provides accurate and reliable condition assessment of insulation in power transformers, paper-mass insulated cables, bushings, and instrument transformers (CTs/PTs). The DIRANA utilises Dielectric Frequency Response (DFR) to determine the moisture content of oil-paper insulated power and instrument transformers. Features: • Non-invasive measurement process • FDS and PDC+ algorithm for fast testing • Results defined by IEC 60422 • Comes with laptop featuring pre-loaded software

Omicron Franeo 800 Sweep frequency response analyser

Sweep frequency response analyzer standard package with PTM software. Fully compliant with the IEC 60076-18 and IEEE C57.149 standards. Suitable for power transformer testing and rotating machines testing & monitoring.

Omicron HGT1 Handheld grounding tester

HGT1 is a handheld meter to measure ground impedance, step and touch voltages. Applications include measuring Fall of Potential at locations outside the substation to determine the ground impedance and measuring step and touch voltages at multiple locations using the CPC 100 and CP CU1.

Omicron HGT1 Handheld grounding tester with PTM

HGT1 with PTM software is a handheld meter to measure ground impedance, step and touch voltages. Applications include measuring Fall of Potential at locations outside the substation to determine the ground impedance and measuring step and touch voltages at multiple locations using either Compano 100 or the CPC 100 and CP CU1.

Omicron Testrano 600 Three Phase Transformer Tester

Omicron Testrano 600 Enhanced package. portable, three-phase test system which supports all common electrical tests on single- and three-phase power and distribution transformers. Tests include Transformer turns ratio (TTR) / exciting current, DC winding resistance, Demagnetization, OLTC scan / dynamic resistance measurement (DRM). Supplied with laptop and PTM advanced software.

Omicron VBO3 Three-phase voltage transformer

VBO3 is a three-phase voltage transformer with a transformation ratio of 1:2 and extends the range of application of a CMC up to 600 V (L-N). Main fields of application are tests in renewable energy plants and industrial networks with 400 V (L-N) [690 V L-L]. The transformer is designed for a nominal frequency of 50/60 Hz, the secondary voltage is load dependent.

Panametrics PM880 Industrial Moisture Analyser

Intrinsically safe moisture analyser for compressed air systems, non-corrosive gases & hydrocarbons such as natural gas (IS certification to ATEX and CSA). Displays dew point, moisture concentration, pressure & temperature. Dew point calibrated measurement range -80~20 degC with data to -110 degC. Pressure range 7~69bar limited by sensor, gauge and safety-valve (operating range from 5µHg). Temperature range -30~70°C. Gas flow operating range from static to 10,000cm/s velocity. Supplied with compact sample system with gauge, safety-valve, sampling valves and fittings (1/4" Swagelok). Data logging of up to 100K moisture points, with infrared port and software for download. Battery powered only (15-24h operation) with second battery and charger (note charger is not IS).

Panametrics PT900 High Penetration Transducers

Panametrics PT900 Transducer and fixture. The fixture is suitable for pipe larger than 150mm up to 1 meter. Transducer type #591 suitable for pipes from 150mm pipe to larger sizes, -40-130 deg C

Panametrics PT878GC-01 ultrasonic gas flow meter Kit

Portable non-contact gas flowmeter using transit-time principle. Compatible with metal or plastic pipes and supplied with transducer kit in the range 20~300mm. Suitable for use with compressed air, natural gas and other gases. Readout for flow velocity, actual or standard volumetric flow or mass-flow in numerical or graphic format. Internal logging for 100K flow data points. USB communications port for download to PC. Rechargeable battery for 8h continuous operation.

Panametrics PT900 Ultrasonic Flowmeter

Panametrics TransPort PT900 is a NATA accredited portable non-contact liquid flowmeter using transit-time principle. Includes thickness gauge and 2 sets of transducers, one 12.5mm to 50mm the second 50mm to 600mm diameters with temperatures ranges from -40 to 210 deg C and -40 to 150 deg C depending on transducers supplied and clamping fixtures. Flow velocity range 0.03 to 12.2m/s. Accuracy typically 1%. Data logging to internal memory, accessed as external drive when plugged into a PC via USB. Setup and monitoring using Android or iOS device. Rechargeable Li-ion batteries and AC power supply/charger. Typical battery life approximately 14 hours.

Panametrics PT900E Ultrasonic Liquid Flow Energy Meter

Panametrics Transport PT900E is a NATA accredited portable non-contact liquid flowmeter using transit-time principle. Includes thickness gauge and 2 sets of transducers, one 12.5mm to 50mm the second 50mm to 600mm diameters with temperatures ranges from -40 to 210 deg C and -40 to 150 deg C depending on transducers supplied and clamping fixtures. Flow velocity range 0.03 to 12.2m/s. Accuracy typically 1%. Data logging to internal memory, accessed as external drive when plugged into a PC via USB. Setup and monitoring using Android or iOS device. Rechargeable Li-ion batteries and AC power supply/charger. Typical battery life ~ 14 hours. Supplied with Energy measurement option to calculate energy flow rate and totalized energy using Analogue I/O. RTD temperature transmitter with range -10 to 150 deg C.

Polysonics Hydra SX30 Dual Freq Doppler Liquid Flowmeter

Dual frequency Doppler ultrasonic non-contact flowmeter. Velocity range 0.06 to 10m/s, accuracy +/-1%. Pipe size range 12~5,000mm diameter. Data logging for 90,000 points, with PC software and interface cable for download via RS232C interface. Transducer temperature range -40~122 degC. Analog output 4~20mA. Battery operated, 12h continuous use (8hr recharge)

Proceq GPR-Live Concrete Ground Penetrating Radar

Portable ground penetrating radar (GPR) for concrete testing. Conducts wide frequency spectrum measurement with Line and Area scan modes. Features a compact, wireless probe with standard rechargeable AA batteries. Proceq GPR Live Basic app supplied with iPad for easy analysis of data on-site

Proceq GPR-Live PRO Concrete Ground Penetrating Radar

Portable ground penetrating radar (GPR) for concrete testing. Conducts wide frequency spectrum measurement with Line and Area scan modes. Features a compact, wireless probe with standard rechargeable AA batteries. Proceq GPR Live PRO software supplied with iPad for easy analysis of data on-site. Addtional capabilities like Pro time-slice view, 3D view, Data sharing and reporting,augmented reality and secure cloud features are available.

Protimeter MMS2 Moisture Measurement System

Moisture meter for detection of moisture in non conductive solid materials such as wood and masonry. Two measurement modes, search for qualitative measurements and measure mode for precise and localised moisture content. Supplied with pin type probes, deep wall probes, hygrometer probe and extension cord,for RH, ambient temperature or dew point temperature. Hygrostick probe supplied for surface temperature measurement. Also includes IR measurement capability. Logging software and USB interface

Proceq Silver Schmidt Live OS8200 N

The Silver Schmidt Live OS8200 N is a high-precision rebound hammer for non-destructive testing of concrete strength and uniformity. Built with Swiss impact technology, it offers automatic impact angle correction and consistent results in any orientation. Fully compliant with EN 12504-2, ASTM C805, ISO 1920-7, and JIS A1155, it ensures international testing standards are met. The OS8200 N integrates with the Screening Eagle platform for real-time data capture, wireless sync, and automated reporting via mobile and cloud apps. Supplied with an android device/phone, it features enhanced signal acquisition, robust construction, and user-friendly operation - ideal for structural assessment, quality control, and inspection of in-situ concrete.

Proceq Pundit PL-200PE Ultrasonic Concrete Test System

PL-200PE ultrasonic concrete test system. This system can determine depth of perpendicular cracks , slab thickness from a single side and it can also locate and measure voids, pipes, cracks parallel to the surface. It will estimate the internal compressive strength of the concrete.

Proceq Profoscope Rebar Locator & Cover Meter

Rebar locator and covermeter. Short range measurements to 95mm. +/- 3mm accuracy. Long range 185mm accuracy +/-4mm. The unit will determine the position of the rebars, the mid point between rebars, Concrete cover, estimation of bar diameter & the orientation of the rebar. Powered by 2 x AA batteries. Battery life 15h with backlight 55h without.

Proceq Resipod Concrete Resistivity Meter

Can determine the likelihood of corrosion and the corrosion rate in concrete. 0 to 1,000kOhm measurement range. USB interface, USB charging. Waterproof.

Proceq SilverSchmidt UN Concrete Test Hammer

The Schmidt hammer requires no corrections for angle of test, simple one button operation, datalogging capability with USB download with detailed reporting capability. Impact Energy 2.207Nm. Compressive strength range 10~170MPa. Battery Life >1000 Impacts before recharging is required.

Profound Vibra Ground Vibration Logger

Designed for long term ground vibration logging. Includes a Geophone and remote alarm with flashing light. Velocity Range 0 to 100mm/s. 4 weeks operation on 3 x D cell batteries. USB interface. Download possible while measuring. Full Windows analysis software included. IP65 case. Meets standards for Vibration in Buildings - Effects on structures and Effects on persons in buildings.

Profound Vibra Wireless Alarm

Add one or more visual alarms to a PRO,VIBRA-CLOUD. These rechargeable alarms wirelessly link with one or more Profound ground vibration monitors. With a 5/8" mounting thread these alarms can be mounted on a standard tripod.

Profound - 50m Geophone Extension Cable

Allows installation of Geophone in hard to reach places while allowing access to the main unit. Also useful to allow access to power or better signal strength

Profound Vibra Cloud Ground Vibration logger

The Profound VIBRA+ is designed for long-term ground vibration logging. It is ideal for applications in the construction industry where safety and environmental considerations must be taken into account. The unit includes SMS alarms and is IP65 rated. Cloud access optional. Download of data is possible without interrupting ongoing measurements and the unit is configured to meet DIN 4150 (part 2, 3 and SBR - part A and B), 'Vibration in buildings - Effects on structures' and 'Effects on persons in buildings' standards. Features: • Long internal battery life • Can be recharged by user supplied USB Power Bank • Velocity range 0 to 100 mm/s • Smart alarm (frequency dependent on velocity according to DIN 4150) • USB interface

Geophone Mounting Plate - Ground/Floor

Machined Stainless Steel Mounting plate for Geophone when deployed on horizontal surface. Ball joint allows geophone to be levelled. 3 reversable feet. Rounded end for deployment on hard surfaces. Spike end for deploment on soft surfaces, such as soil or through carpet.

Pruftechnik Tension chain and Tip rod Kit

Kit of addtional Tension chains and Tip rods for Pruftechnik Laser shaft alignment system

Pruftechnik Optalign Touch Standard Optical Alignment System

Pruftechnik Optalign Touch Standard optical alignment system with 5 axis precision sensors. Includes target, thermal growth and dial gauge input. Multipoint measurement. and Spacer measurement. Compact magnetic brackets. Reliability centre software included.

PVE PVPM1540X Solar IV Curve Tracer

The PVE PVPM1540X Solar IV Curve Tracer is a high-precision instrument designed for professionals seeking advanced solar panel testing and performance analysis. Available exclusively for rent or hire, this device is essential for engineers, solar installers, and maintenance teams who require accurate, on-site measurement of photovoltaic (PV) module and string characteristics. The PVPM1540X streamlines the process of indoor and outdoor solar IV curve tracing, enabling efficient diagnostics, commissioning, and quality assurance of solar installations. Manufactured by Photovoltaik Engineering, the PVE PVPM1540X Solar IV Curve Tracer is engineered for robust field use and delivers reliable results across a wide range of PV system configurations. This advanced tool measures current-voltage (IV) characteristics, calculates maximum power point (MPP), and provides detailed analysis of module and string performance. With intuitive operation, high measurement accuracy, and compatibility with various PV technologies, the PVPM1540X is ideal for professionals who demand precise solar testing without the commitment of ownership. Whether you need to rent or hire a solar IV curve tracer for commissioning, troubleshooting, or routine maintenance, the PVPM1540X ensures your solar assets perform at their best. Key Features: High-Precision IV Curve Measurement: Accurately captures current-voltage characteristics for PV modules and strings, supporting detailed performance analysis. Maximum Power Point (MPP) Calculation: Automatically determines the MPP for optimal system efficiency and diagnostics. Wide Voltage and Current Range: Supports measurements up to 1500V and 40A, accommodating modern high-capacity PV systems. Field-Ready Design: Rugged, portable construction ensures reliable operation in challenging outdoor environments. Comprehensive Data Logging: Stores measurement data for later review and reporting, streamlining documentation and compliance. Why Choose the PVE PVPM1540X Solar IV Curve Tracer? Delivers industry-leading accuracy for reliable solar performance assessments. Versatile compatibility with a broad range of PV modules and system sizes. Streamlines testing and analysis, saving time and reducing operational costs. TechRentals provides the PVE PVPM1540X Solar IV Curve Tracer on flexible rental terms, giving you access to premium equipment without the upfront cost of ownership. Backed by over 50 years of industry expertise, we help ensure accurate and efficient solar system performance verification. Enquire today to rent the PVE PVPM1540X Solar IV Curve Tracer and streamline your solar IV curve testing and performance analysis tasks. Not sure which equipment to hire? Call our friendly experts today and get the right solution for your project.

Rion NL52EX SLM with NX42RT Octave and 1/3 Analyser

Rion NL52EX Type 1 Sound Level Meter, including the Octave and 1/3 Octave measuement option NX42RT. This meter can be used to check NC levels for compliance checking. The instrument includes a NATA calibrated calibrator. All data is save to an SD card.

Rion VA-12 Vibration Analyser

Vibration analyser. Includes magnetic pickup type. Will store measurements. Measures acceleration, velocity and displacement and displays it in either time or frequency domain. It will display rms, peak and crest factor. Uses FFT to display power and vibration spectrum. Incorporates SD card memory storage.

RKI Eagle2 Gas Detector, Confined Space plus PID

RKI Eagle2 measures 4 confined space gasses CH4, O2, H2S and CO plus a PID. Alkaline 18 hours or Ni-MH 20 hours capability. Powerful long-life pump up to 38m range. Low flow pump shut off and alarm. Datalogging standard. IrDA communications port. Autocalibration/ single gas calibration. Internal hydrophobic dust filter. External probe with hydrophobic filter. Ergonomic RFI/EMI/chemical/weather resistant enclosure. Intrinsically safe design, CSA approval.

Seaward Solar Utility Pro Kit

Seaward Solar Utility Pro Kit - 1500V / 30A, 1000V / 40A, maximum power 45kW. Test multiple strings in parallel up to 1500V / up to 40A. Tests open circuit voltage (Voc), short circuit current (Isc), irradiance (W/m2), ambient temperature & more. Recording up to 999 full sets of string data.

Simco-Ion FMX-004 Electrostatic Fieldmeter

The FMX-004 fieldmeter is a compact electrostatic fieldmeter used for locating and measuring static charges. Its pocket size and three-button operation makes it convenient and easy to use. Automatic range switching up to ±30 kV, digital and bar graph display with +/- indicators, audible alarm.

Softing BC-700-PB Profibus Tester 5, PB-T5

The PROFIBUS Tester 5 (BC-700-PB) is a powerful diagnostic and troubleshooting tool for testing cables, measuring signals and analysing the communication of PROFIBUS networks. Its battery-powered and provides a graphical display, allowing for quick results when working in stand-alone mode. In addition, the BC-700-PB supports the export of test results for advanced analysis.

Spektra CV-10 portable vibration calibrator

Spektra CV-10 portable vibration calibrator with proximity probe adaptor and sweep frequency option. Suitable for accelerometers, velocity transducers and proximity probes.It can provide 5Hz to 10kHz vibrations. Maximum amplitude 20g (no load). Maximum payload 900gram.

Stalker PRO II radar speed gun kit. Including large display

Stalker PRO II-KIT includes a radar gun, tripod & large 3.5 digit display with 20cm high digits. Includes 4 modes of operation, Carnival, Baseball, Tennis and Vehicle modes. Operates at upto 1290kph.

Tour & Anderson Scope Balancing Meter

Digital flow balancing instrument with color display. For cooling water valve balancing in air conditioning plants and similar applications. Includes facility for entry of Kv value to allow balancing of all hydronic valve types. Differential pressure range -0.5~20.5m water gauge at a total pressure of less than 200m. Resolution 0.001m. Flow resolution 0.001l/s. Battery operated.

Testo 174H Temp & Humidity Logger Kit of 20

Testo 174H temperature & humidity dataloggers Kit of 20 . -20~70DegC+/-0.5 Deg C 0~100%RH +/-4% (2~98%RH). 160000 readings up to 1min sample rate. 1 year battery life (@15min intervals)

Testo 175-H1 Temperature & Humidity Logger

Testo Temperature & Humidity Logger. Large Display. 3 year battery life, 1 million sample memory. RH 0 ~100% +/- 2%, temp -20~50 degC +/-0.4 degC. Includes USB interface to download data

Testo model 340 portable flue gas analyser

Testo 340 flue gas analyser. Includes O2, CO (h2 compensated), CO2 (calculated), NO & NO2 sensors. 335mm engine probe suitable for diesel and boiler testing with temperate probe, 350mm pitot tube, Bluetooth printer & easy emission software.

Testo 350 Flue Gas Analyser

Testo 350 Flue gas analyser with built in Peltier gas preparation (chiller). Measures O2, CO, NO, NO2, and SO2 concentrations. Calculates CO2 concentration. Ranges: O2 0-25% vol, CO with H2 compensation 0-10000 ppm, NO 0-4000 ppm, NO2 0-500 ppm, SO2 0-5,000 ppm, Comes 0600 7555 Engine probe with temperature up to +1,000 deg C. easy emission software, Battery and AC mains operation.

Testo 400 logger with Temp/Hum/AbsPress, Hot Wire Probe

Testo 400 loggin instrument including a Bluetooth extendable probe 0635-1571 measures Temperature -20~70DegC, Humidity 5~95%, Abs Pressure 700~1100Hpa & Hot Wire air velocity 0~50m/sec. Extension 57cm~100cm. The instrument itself has Differential Pressure -100~200Pa and Absolute Pressure -700~1100HPa. Displays Dewpoint. Extensive communications capability including email, bluetooth, PC management software and even teamviewer fro remote control.

Testo 417 100mm vane anemometer

Vane anemometer 100mm head. Display velocity and temperature. Has averaging function to measure ducts. 0.3~20m/sec +/-(0.1m/s + 1.5% mv) Temperature 0~50DegC +/-(0.5DegC). 50Hr battery life.

Testo 420 Air balancing flow hood system

Testo air balancing flow hood kit. Includes 610x610, 360x360, 305x1220, 610x1220 hoods and stand and 500mm pitot tube. Measures 40~4000m3/hr +/-3%, Temperature 0~70DegC +/-0.5DegC -20~0DegC +/-0.8DegC, 0~100%RH +/-1.8%+3%Rdg, Differential Pressure 0~120Pa +/-2%Rdg+.05Pa. Kit includes a stand and an Android or iPhone app can be downloaded for one man remote operation. Kit includes 500mm pitot tube.

Testo 420 Differential Pressure Instrument

Testo 420DP is used for volume flow measurements, Pitot tube measurements and pressure measurements for air conditioning and ventilation systems. Measuring ranges: Flow velocity: 0 to 14 m/s, Pressure (absolute pressure):70 to 110 kPa, Pressure (differential pressure): -120 to +120 Pa. Resolution: Flow velocity: 0.01 m/s, Volume flow: 1 m³/h, Pressure (absolute pressure): 0.1 hPa / 0.1 mbar / 0.01 kPa, Pressure (differential pressure) 0.00001 hPa / 0.00001 mbar / 0.0001 mm H2O / 0.000001 inH2O. Storage temperature: -20 to +60 °C, Operating temperature: -5 to +50 °C

Testo 440 with Temperature Humidity probe

Testo 440 with 0636 9770 High precision Temperature and Humidity probe,Blutooth capable. Measuring range - 0 to 100 %RH and -20 to +70 deg C. Accuracy ±(0.6 %RH + 0.7% of m.v.) (0 to 90 %RH), ±(1.0 %RH + 0.7% of m.v.) (90 to 100 %RH) and ±0.3 °C (15 to 30 °C), ±0.5 °C for remaining meas. range. Resolution - 0.01 %RH and 0.1 °C

Testo 635-2 Humidity, Temperature & Dewpoint Meter

Portable humidity meter fitted with robust stainless probe with sintered filter-cap for general or duct measurements to 120 degC, and fast-action K-type surface temperature probe. Displays relative humidity, absolute humidity, dew point, degree of humidity, enthalpy, temperature, and differential temperature (dewpoint~surface). Operating range 2~98%RH (+/-2%). Air temperature -20~120 degC (+/-0.2/0.5). Surface temperature -60~300 degC (+/-0.1). Internal memory for 10,000 values with USB interface, cable and software for download and presentation. Battery operated.

Testo 635-2 Temp & Dewpoint Meter for compressed air systems

Portable humidity meter fitted with 0636 9836 HPD pressure dewpoint probe for measurements in compressed air systems, -60 to +50DegC tpd, 0~100%RH. Internal memory for 10,000 values with USB interface, cable and software for download and presentation. Battery operated. Maximum pressure 15bar

Teseq NSG 437 30kV Static Discharge Generator

Ergonomic design and advanced functionality. The NSG 437 ESD simulator is designed to sit comfortably in the operator’s hand, with operating conditions constantly displayed and accessible on a bright, clear colour touch display. Features • Air and Contact discharge to 30 kV • Easily and quickly interchangeable discharge networks • Activity log

Thermoline TU3 Temperature Bath

The Thermoline TU3 Temperature Bath is a precision-controlled laboratory water bath designed for accurate temperature calibration, testing, and sample incubation. Ideal for professionals in research, calibration laboratories, and industrial quality control, the Thermoline TU3 Temperature Bath delivers reliable temperature stability and uniformity, making it essential for applications requiring consistent thermal environments. Manufactured by Thermoline, a trusted name in laboratory equipment, the TU3 Temperature Bath is available for rent or hire, providing a flexible solution for short-term or project-based needs. This temperature bath features a robust stainless steel tank, digital temperature control, and a wide operating range, ensuring precise and repeatable results. Whether you need to calibrate instruments, conduct thermal testing, or maintain samples at specific temperatures, the Thermoline TU3 Temperature Bath offers the performance and reliability required by technically minded users. Key Features: Digital Temperature Control: Achieve precise temperature settings and stability for accurate calibration and testing. Wide Temperature Range: Supports a broad operating range, suitable for various laboratory and industrial applications. Stainless Steel Construction: Durable tank ensures long-lasting performance and easy cleaning. Uniform Temperature Distribution: Advanced circulation system maintains consistent temperatures throughout the bath. Large Capacity: Accommodates multiple samples or instruments for increased productivity. Why Choose the Thermoline TU3 Temperature Bath? Delivers highly accurate and stable temperature control for critical laboratory processes. Engineered for reliability and ease of use in demanding professional environments. Versatile design supports a wide range of calibration, testing, and incubation tasks. TechRentals provides the Thermoline TU3 Temperature Bath on flexible rental terms, giving you access to premium equipment without the upfront cost of ownership. Backed by over 50 years of industry expertise, we help ensure precise and reliable temperature calibration and testing. Enquire today to rent the Thermoline TU3 Temperature Bath and streamline your laboratory temperature calibration and testing tasks. Not sure which equipment to hire? Call our friendly experts today and get the right solution for your project.

Topcon HiPerCR Network Rover with Controller &"Topcon Field"

Building upon the previous HiperSR model, the Topcon HiperCR network rover adds full constellation support and delivers better performance in challenging GNSS areas, within an even smaller and lighter package. • Requires network coverage (RTK access provided) • Topcon Field software only (contact us if you require Pocket3D)

Topcon HiPerSR Network Rover with Controller, Pocket 3D

Topcons HiPer SR receiver is a lightweight and completely integrated GNSS receiver (GPS plus Glonass) for real-time cm level accuracy anywhere within a GPS network where there is mobile signal. It is an ultra-lightweight and easy to use network rover. The HiPer SR weighs only 800gm and has an IP67 environmental rating means you can rely on its performance even in the harshest conditions. It is an ultra-lightweight and easy to use network rover for simple or complex surveyin surveying tasks. This 100% integrated receiver operates cable-free, with no antennas, battery doors or connectors to worry about. It connects via Bluetooth to the FC-5000/FC-6000 controller running Magnet and Pocket 3D software. Features: • Easiest to use and lowest rental rate of any GNSS Rover • Ideal for a non-surveyor wanting simple site positioning • Lightweight with carbon fiber pole • Ideal for simple pick-up and stakeout surveying tasks • Large 7" map display

Topcon IM-2D Lux Meter

The Topcon IM-2D Lux Meter is a precision instrument designed for professionals who require accurate measurement of illuminance in a variety of environments. Ideal for lighting engineers, facility managers, and environmental consultants, the Topcon IM-2D Lux Meter is available exclusively for rent or hire, making it the perfect solution for temporary projects or short-term needs. This advanced lux meter ensures reliable indoor air quality monitoring and lighting assessments, helping you maintain optimal lighting conditions for safety, compliance, and productivity. Manufactured by Topcon, a global leader in precision measurement technology, the IM-2D Lux Meter offers high sensitivity and a wide measurement range, making it suitable for both low-light and high-intensity applications. With its user-friendly interface and robust design, this lux meter delivers fast, accurate readings for a range of professional applications, including workplace safety audits, lighting design verification, and environmental monitoring. The Topcon IM-2D is engineered to meet the demands of technically minded users, providing dependable performance and detailed data output for comprehensive analysis. Key Features: Wide Measurement Range: Accurately measures illuminance from low to high lux levels, suitable for diverse lighting environments. High Sensitivity Sensor: Delivers precise readings even in low-light conditions, ensuring reliable data for critical assessments. Digital Display: Easy-to-read digital interface provides clear, real-time lux measurements for efficient monitoring. Data Hold Function: Allows users to freeze readings on the display, simplifying data recording and analysis. Portable and Durable Design: Lightweight construction with robust housing for convenient use in the field or on-site. Why Choose the Topcon IM-2D Lux Meter? Delivers highly accurate and consistent illuminance measurements for professional applications. Offers flexible functionality to suit a wide range of lighting assessment tasks. Engineered for ease of use, making it accessible for both experienced and new users. TechRentals provides the Topcon IM-2D Lux Meter on flexible rental terms, giving you access to premium equipment without the upfront cost of ownership. Backed by over 50 years of industry expertise, we help ensure accurate and efficient lighting assessments. Enquire today to rent the Topcon IM-2D Lux Meter and streamline your lighting measurement and assessment tasks. Not sure which equipment to hire? Call our friendly experts today and get the right solution for your project.

Topcon LN-150 Robotic Total Station with Controller

The Topcon Layout Navigator 150 is an extremely easy to use Robotic Total Station ideal for those needing high accuracy. Range 0.9 to 130 m, accuracy +/- 3mm. Easy operation for the non-surveyor. Features: • Self Leveling for easy setup. Setup over a point, or observing 2+ known points • Uses the same easy to use Magnet Field software as the Topcon GPS systems • Ideal for pick-up or layout to a few mm accuracy

Remote Area Power Supply 55Ahr

Remote Area Power Supply 55AHr Lithium Battery with 12V output. To be used with TR,SOLAR. 2 Solar panels can be connected if necessary.

Solar Panel compatible with 150AH Remote Access Power Supply

Solar Panel 200W to be used with the TR,RAP-150AH system. With free standing frame., These can be daisy chained together for higher wattage.

Solar Panel compatible with 55AH Remote Access Power Supply

Solar Panel 130W to be used with the TR,RAP-xxAH system. With free standing frame., These can be daisy chained together for higher wattage.

Trimble R12 LT UHF Base Kit

The Trimble R12 LT UHF Base kit is designed for use with a tripod and broadcasts RTK corrections using an internal 2W UHF radio. Pair with a Trimble UHF Rover kit to achieve cm-level RTK positions when working outside of CORS network areas. Use with an optional Trimble TDL450 UHF Repeater kit to increase radio range. Features: " Includes tribrach, adapter, base pole extension, 6Ah battery " Configure Base using WebUI or controller " Complimentary tripod available on request

Trimble R12 Network Rover with Controller

Building upon the foundation laid by the R10-2 and HD-GNSS, the Trimble R12 GNSS receiver is engineered for improved performance in challenging GNSS conditions. Push your GNSS surveying further than you ever thought possible with Trimble's latest developments in GNSS signal management. Features: • TSC7 Controller with Trimble Access • Trimble's new ProPoint processing engine better maintains high GNSS performance in sky-obstructed urban and natural environments. • Includes VRSNow network RTK access

Trimble R12 LT UHF Rover with Controller

The Trimble R12 LT UHF Rover kit with ProPoint GNSS signal processing enables industry-leading GNSS performance in sky-obstructed urban and tree-covered environments. Pair with a Trimble UHF Base kit to achieve cm-level RTK positions when working outside of CORS network areas. Features: " Includes TSC7 tablet controller and pole " Trimble Access and Roads software " Requires nearby GNSS Base with UHF radio (or other BYO correction service) for cm-level RTK accuracy

Trimble S5 1sec Robotic TS with Controller

The Trimble S5 robotic total station is a workhorse for general surveying tasks. The included MultiTrack active prism features an array of infrared LEDs to ensure the instrument can only find and track your prism, avoiding false reflectors and reducing downtime. The Tracklight offers remote instrument guidance at a distance. Features: - 1" second robotic with Tracklight - TSC7 controller with Trimble Access - MultiTrack prism and pole

Trimble S7 1sec Robotic TS with Controller

Extend your robotic total station capabilities with the Trimble S7. Over the S5 the S7 adds the VISION remote video feed and SureScan area scanning. VISION video allows you to view, capture and control instrument aiming while working away from the instrument. SureScan enables basic point scanning with consistent point spacing throughout. Features: - 1" second robotic with VISION video feed - TSC7 controller with Trimble Access - MultiTrack prism and pole

Trimble S9 1sec Monitoring Robotic Total Station

TRI,S9_1SEC The Trimble S9 robotic total station is designed for monitoring, tunnelling, rail and other specialised applications. Features: - 1" second robotic with VISION, DR HP EDM and FineLock - DR HP EDM offers increased prism measurement accuracy - FineLock sensor can better detect separate prisms that are spaced closely together

Trimble X7 Laser Scanner

The Trimble X7 scanning system delivers powerful performance with simple operation. This is ideal for the surveyor, and non-surveyor alike. Features: • Export a combined Point Cloud straight from the tablet in the field • Automated survey grade self-leveling • Trimble Registration Assist for automatic registration • Complete with Tripod and T10 Tablet

TSI VelociCalc 100mm Vane Anemometer

TSI 5725 is a 100mmm reversible vane anemometer and temperature probe. Logs 12700 samples Displays velocity and temperature. Calculates volumetric flow rate when user inputs duct shape and size or area. Anemometer accuracy 1.0% of reading +/-0.02m/sec. Temperature Accuracy +/-1.0DegC. NATA calibration certificate included.

TSI Q-TRAK IAQ Monitor CO2, CO Temperature & Humidity Logger

TSI 7575 with IAQ probe model 982. Measures CO2 0~5000ppm +/-3%, temperature 0~60 degC +/-0.6 degC, humidity 0~95% +/-3% , CO 0~500ppm +/-3% and barometric pressure 517.15~930.87mmHg +/-2%. Calculates dew point, wet bulb and percent outside air. Displays 5 measurements simultaneously. User selectable logging interval and start stop times. Stores 39 days data at 1min intervals 56,035 data points. This unit also has external thermocouple measurements.

TSI 8710 DP-CALC Differential Micro Manometer

Micro-manometer for static or differential pressure, velocity, volumetric flow, atmospheric pressure and temperature. With statistical analysis, density correction, K factor and automatic actual/standard flow calculation. Differential pressure range +/-3735Pa. Velocity display to 41m/s (range depends on probe). Supplied with static tip, pitot tube, velocity matrix and temperature probe. Datalogging (1,000 point) with RS232C interface and software. Rechargeable cells or AC adaptor.

TSI Aerotrak Handheld Particle Counter 9306 V2

TSI AeroTrk Hand Held Particle Counter generates Pass/Fail reports for ISO 14644-1, EU GMP Annex1 and FS209E. Count particle sized 0.3~25um, flow rate 2.83L/min. Counts 6 channel sizes. Includes data storage and download.

TSI 9565A Velocicalc Air Conditioning Efficiency Meter

Portable efficiency measurement system for HVAC and related work, with hot wire anemometer, static and differential pressure, temperature and humidity measurement with heat flow efficiency calculation. Velocity (hot wire) 0 to 50m/s, accuracy +/-3%. Temperature -10 to 60 degree C, accuracy +/-0.3. Wet bulb temperature 5 to 60 degree C. Relative humidity 0 to 95%RH, accuracy +/-3%. Dewpoint -15 to 49 degree C. Static/differential pressure -3,735 to 3,735Pa, accuracy +/-1%. Probe length 1m, tip diameter 7mm, base diameter 10mm. Includes data logging and printing. Battery operated. USB & Bluetooth download.

UE Systems UP3000 Digital Ultrasonic Leak Detector

The Ultraprobe 3000 KIT ultrasonic inspection system. Displays dB levels. Readings can be stored and downloaded. A tone generator is supplied together with a stethoscope probe and a rubber focusing probe. Interface software to download readings is also supplied.

VeEX Ethernet Services Test Set 10G

The MTX150x is a self-contained Ethernet services test solution for Layer 1 to 4. Required by field technicians to install, verify, maintain and troubleshoot Metro Ethernet links, Business services, Internet Access and other packet-base services up to 10 Gbps. Ethernet Testing includes BERT, RFC2544, Throughput, Y.1564, Optical Lane BERT, Loopback, PCS Analysis, Multiple Stream (32), IP Connectivity and IPv6. Ethernet Layer-4+ Testing: V-PERF 1GE/10GE Line Rate TCP Throughput per RFC6349.

VeEX Ethernet Services Test Set 1G

The MTX150x is an Ethernet services test solution for Layer 1 to 4. Required by field technicians to install, verify, maintain and troubleshoot Metro Ethernet links, Business services, Internet Access and other packet-base services up to 1 Gbps. " Loopback device included " RFC2544 " V-SAM test suite compliant with ITU-T Y.1564 standard " Throughput, BERT, IPv4/IPv6

VeEX Ethernet Services Test Set 100G

VeEX TX300 100G Ethernet test set. Fast troubleshooting and comprehensive analysis of transmission problems can be performed using its common graphical user interface. Novice users benefit from the easy-to-use GUI, while experienced users will appreciate an array of advanced features. Applications include installation, commissioning, monitoring and maintenance of Ethernet networks. Features " 100 Gbps Ethernet testing " RFC2544 and V-SAM (Y.1564) testing " IPv4 and IPv6 traffic generation " Fibre Channel " OTN

Viavi MTS-4000 Multi and Singlemode OTDR

Viavi MTS-4000 Single-Mode OTDR

Viavi Single-mode OTDR 1310/1550/1625nm with a SC/A connector and dynamic ranges 40, 40 and 38 dB respectively. The fibre module is housed in the 9" touch screen MTS-4000 mainframe and is capable of point to point and up to 32x splitter FTTx/PON testing. It features the Smart Link Mapper function which offers the user an easy to follow block diagram as well as the OTDR trace, helping novice and expert Fibre Technicians alike. Supplied with a P5000i VIP and launch lead.

Wika GIR-10 SF6 Gas detector

Wika GIR-10 SF6 Gas Detector. Gas detector based on infrared technology. Responds only to SF6 gas, therefore not sensitive to humidity and common VOC. Fast response time. Smallest concentrations of up to 0.6 ppmv can be detected. Applications include Locating and quantifying leakages at SF6 gas filled equipment, Determination of leak rate for final inspection of SF6 gas. filled equipment

Wohler VIS-500 Service Camera Visual Inspection System

30-meter compact colour video inspection system with 26mm forward facing camera head waterproof according to IP68 and a 40mm Pan Tilt colour camera, waterproof according to IP67 with a viewing angle of 130 degrees. TFT display with Lithium -Ion Battery life up to 6 hours. Supplied with L200 locator. Applications include damage analysis in water / drainage / sewer pipes, inspection of hollow spaces, ventilation, machines, control panels, exhaust systems and production surveillance.

Yokogawa 51012 Lux Meter

Digital illuminance meter. Measuring range from 0 to 99.9/999/9,990/99,900/999,000lx . Accuracy <3,000lx 4% +/-1 digit >3,000lx 6% +/-1 digit. Autoranging with silicon sensor. Battery operated and certified ISO/IEC 17025.

Evident UT Probe Kit

Ultrasonic Probe Kit with Various probes and wedges.

Additel 681AEx Digital Logging Pressure Gauge 20 bar

Additel 681AEx digital pressure gauge. Range: -1 to 20 bar, (-100 to 2,000 kPa), (-15 to 300 psi). " Gauge or Absolute pressure " Data logging (up to 10,000,000 records) " Intrinsically safe " Bluetooth communication " Accredited to ISO/IEC 17025 NATA certified

Evident SteerRover Industrial Scanner

SteerRover Scanner for Weld Inspection and Corrosion Mapping. Fully automated, steerable motorised 2-axis scanner for inspections of large ferromagnetic surfaces, such as pressure vessels and tanks, and achieve reliable phased array (PA) ultrasonic testing of areas that are difficult to reach.

Additel 681AEx Digital Logging Pressure Gauge 70 bar

Additel 681AEx digital pressure gauge. Range: 70 bar, (6,900 kPa), (1000 psi). " Data logging (up to 10,000,000 records) " Intrinsically safe " Bluetooth communication " Accredited to ISO/IEC 17025 NATA certified " Ambient temperature logging

Evident Phased Array Probe Kit

Phased Array Probe Kit with Various probes, Wedges and Encoder. Please contact TechRentals for probes supplied.

Additel 681AEx Digital Logging Pressure Gauge 700 bar

Additel 681AEx digital pressure gauge. Range: 700 bar, (70,000 kPa), (10,000 psi). " Data logging (up to 10,000,000 records) " Intrinsically safe " Bluetooth communication " Accredited to ISO/IEC 17025 NATA certified " Ambient temperature logging

Evident Nortec600 Weld Scan Probe Kit

NEC-8196L WELD INSPECTION KIT for Nortec N600D. Supplied with PowerLink version (7 pin LEMO connectors) containing 1 each of the following: WLD-5-63/7L (9403362) WLD-8-55/7L (9403356) NEC-2236/7L (9403361) SRSM-51020S-WLD (includes certification) WLD-SAMPLE (does not include certification) and CL/SC/6 cable

Evident HydroFORM2 Industrial Scanner

HydroFORM semiautomated scanner for Corrosion Mapping. 2-axis encoding phased array (PA) solution, enables fast and reliable wall-thickness mapping and mid wall damage detection by acquiring high-resolution data of large surfaces in minimal time.

Evident Cobra Scanner

Crystal XP2i Digital Logging Pressure Gauge 20 bar

Range -1 to 20 bar (300 psi) Nata certified pressure gauge. Accuracy, +/-0.1% of reading between 20 to 100% of full scale, +/-0.02% of full scale between 0 to 20% of full scale. Generation 3 gauges have 32,000 point logging capacity at intervals from 1 second to 18 hours, ULP (Ultra Low Power) setting allowing logging for 1 year and PSV/PRV (Pressure Safety/Pressure Relief Value) mode increasing measurement rate to approx. 8x per second. Gen 2 gauges have 6,000 points and logging intervals from 1 second to 18 hours. Logs actual pressure, average pressure, average pressure with peaks and, on demand. Intrinsic and safety ratings registered under IECEx, ATEX and DNV standards.

Crystal XP2i Digital Logging Pressure Gauge 70 Bar

Range -1 to 69 bar (1,000 psi) Nata certified pressure gauge. Accuracy, +/-0.1% of reading between 20 to 100% of full scale, +/-0.02% of full scale between 0 to 20% of full scale. Generation 3 gauges have 32,000 point logging capacity at intervals from 1 second to 18 hours, ULP (Ultra Low Power) setting allowing logging for 1 year and PSV/PRV (Pressure Safety/Pressure Relief Value) mode increasing measurement rate to approx. 8x per second. Gen 2 gauges have 6,000 points and logging intervals from 1 second to 18 hours. Logs actual pressure, average pressure, average pressure with peaks and, on demand. Intrinsic and safety ratings registered under IECEx, ATEX and DNV standards.